manualshive.com logo in svg

Markes International UNITY-Air Server-xr, Руководство по установке

Поделиться
Скачать
Markes International UNITY-Air Server-xr Скачать руководство пользователя страница 14

 

 

 

 

QUI-1122 

Page 14 

Markes International Ltd 

T:

 +44 (0)1443 230935   

F:

 +44 (0)1443 231531   

E:

 [email protected] 

 

www.markes.com 

3.2.4

 

Cable connections 

 

Connect the power cable (

SERZ-0024

). 

Connect the UNITY–Air Server-xr to the PC using the serial cable supplied in the shipping kit (

SERZ-0189

). 

If there are no available serial ports on the PC, use the USB-Serial cable (

U-USBSR

) provided. 

Connect the GC cable. Depending upon the GC that is being used a different connection cable will be 

required: 

SERUTE-5142 

= AGILENT GC 

SERUTE-5143 

= THERMO GC 

SERUTE-5144 

= VARIAN GC 

SERUTE-5141 

= SHIMADZU / OTHER GC 

 

3.3

 

Installing the Transfer Line 

UNITY–Air Server-xr is supplied with a universal transfer line (

SERUTE-5330-xr

) to convey desorbed 

analytes from UNITY–Air Server-xr to a gas chromatograph or other analytical system. The sample path 
utilises a deactivated fused silica line (0.25 mm I.D. an d 0.35 mm O.D.) heated over its entire length by 
means of a distributed heater and at the GC end by heat conduction from the GC oven. The line is 1.4 m 
long, which is sufficient to reach most gas chromatographs even when a mass spectrometer is attached. 

NOTE

:   The parts supplied can be used in other combinations to suit particular instrument configurations. 

3.3.1

 

Installing the Transfer Line onto the GC 

There are two options for transfer line installation; one requires use of a hole in the top, side or back of the 
GC oven, while the other option is to gain access via an unused heated injector port. 

Option 1 – Through Hole in Oven Wall 

1.

 

Locate a hole in the inner oven wall with a corresponding hole leading to the outside of the 
instrument. 

2.

 

Where necessary, displace the oven insulation material such that the transfer line heater can be 
fitted directly against the external face of the oven wall. 

3.

 

Place one of the washers provided in the UNITY-xr shipping kit on the external face of the oven 
wall, over the hole through which the transfer line will be passed. 

NOTE

: A number of different washers are provided.  The washer required will be determined by the 

hole in the oven through which the transfer line will pass. 

4.

 

Fit the GC end of the UNITY-xr transfer line through the hole in the washer and on through the hole 
in the GC oven wall. 

Содержание UNITY-Air Server-xr
















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды