manualshive.com logo in svg

Markes International UNITY-Air Server-xr, Руководство по установке

Поделиться
Скачать
Markes International UNITY-Air Server-xr Скачать руководство пользователя страница 40

 

 

 

 

QUI-1122 

Page 40 

Markes International Ltd 

T:

 +44 (0)1443 230935   

F:

 +44 (0)1443 231531   

E:

 [email protected] 

 

www.markes.com 

 

 

 

 

The carrier gas out line from the Shimadzu AFC (“CG Out”) is now connected to the “Carrier Inlet” port 
on the back of UNITY–Air Server-xr using a 1 m length of green PEEK tubing. 

 

The “Pressure Outlet” from the back of UNITY-xr is now connected - with a similar length of green 
PEEK tubing - to the molecular sieve filter on the septum purge line (and hence to the (“SP In”)) on 
the Shimadzu AFC.  It is important that the two lengths of green PEEK tubing are the same length.  
Carrier gas is supplied and regulated upstream of the system in the supply line and it’s pressure is 
monitored downstream of the system in the septum purge line. 

6.3.2

 

Configuring the Shimadzu GC software 

 

The inlet Split Mode on the Shimadzu GC must be set to Direct.  

a.

 

To access the Split Mode press the “FLOW” key on the GC keypad. 

  NOTE:

   In the case of GCs with two or more AFC units it may be necessary to press the “FLOW” key 

repeatedly until the correct one is displayed. 

b.

 

Move the flashing cursor over the “Split Mode” (type using the arrow keys on the GC keypad). 

c.

 

Using the right arrow key, select “DIRECT” mode as shown, and press the “ENTER” key on the GC 
keypad. 

 

Setting Inlet Mode as Direct on Shimadzu GC 

 

Shimadzu fitting on 

carrier gas line 

Molecular Sieve filter on 

septum purge line 

Two lengths of PEEK tubing 

connecting to UNITY-xr 

Содержание UNITY-Air Server-xr
















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды