manualshive.com logo in svg

Markes International UNITY-Air Server-xr, Руководство по установке

Поделиться
Скачать
Markes International UNITY-Air Server-xr Скачать руководство пользователя страница 38

 

 

 

 

QUI-1122 

Page 38 

Markes International Ltd 

T:

 +44 (0)1443 230935   

F:

 +44 (0)1443 231531   

E:

 [email protected] 

 

www.markes.com 

 

 

Carrier and septum purge lines extended with unions and PEEK tubing 

The stainless steel tubing for the carrier supply line is 1/16” while the septum purge line is 2mm and will 
require a different ferrule when connected to the 1/8” brass union. 

NOTE

:   two 1/8” brass unions, 3 m of 1/16” green PEEK tubing and 1/8” graphitized vespel ferrules, 

including one for 2 mm tubing, are all contained within the UNITY–Air Server-xr shipping kit.)  

 

Connect the carrier gas supply line to the ‘Carrier Inlet’ port of UNITY–Air Server-xr and connect the 
septum purge line  to the ‘Pressure Outlet’ port. 

6.2.2

 

7890 Inlet Setup 

There are several settings that must be implemented on the 7890 whenever the split/splitless EPC 
module is controlling the carrier gas supply to the UNITY-xr thermal desorber.  In the Inlet settings the 
mode must be set to ‘Splitless’, the purge time must be set to exactly ‘999.99’ minutes and Gas saver 
should be set to ‘Off’.  In the Instrument Configuration menu the Auto prep run should be set to ‘Off’. 

Having completed this, the system should now be ready to use. 

 

 

 

 

6.2.3

 

7890 Inlet Settings 

If the pressure is not correctly controlled after inputting the above settings then turn ‘Auto prep run’ to 
‘On’.  

 

Lines cut here 

1/8” Unions allowing 

extension of gas lines 

Содержание UNITY-Air Server-xr
















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды