Mac Medical D Series Скачать руководство пользователя страница 22

Страница: 22 / 48

Instruction Manual

MAN-001

www.macmedical.com

Troubleshooting

The following alert messages and operating conditions will occur when the warming cabinet is operating

outside of acceptable conditions.

Overheat Alarm (HI) Condition

When the cabinet temperature exceeds the setpoint by 10°F (or by 5°C) or the set temperature is lowered

by more than 10°F (or by 5°C), the display will red HI and the audible alarm will sound. Silence the alarm by

pressing ALARM RESET (Up ▲ arrow) until the alarm quits.

Turn off the Warming Cabinet chamber and wait for the contents to cool adequately. Then unload the

contents using personal protective equipment to avoid injury. Reload the contents using the proper loading

guidelines as previously mentioned in this manual.

Turn on the chamber and monitor performance. If the chamber continues to overheat into an alarm (HI)

condition, turn off the chamber and contact your MAC Medical authorized service personnel.

Troubleshooting Guide

Alerts & Description

Action Required

with audible alarm

Cabinet temperature is 10°F (or 5°C) higher than setpoint. Silence the alarm by pressing

ALARM RESET (Up ▲ arrow) and open door(s) to allow the chamber(s) to cool.

LLLL

Input temperature is lower than input range. Check temperature probe and

connections. See below for additional troubleshooting.

HHHH

with audible alarm

Input temperature is higher than input range. Check temperature probe and

connections. See below for additional troubleshooting.

OPEn

with audible alarm

Temperature probe is at fault. Check connection, then replace and calibrate.

JIC

continuous or flashing

Control failure. Check connection first, then replace and calibrate.

Unit will not power up

1. Check outlet for power

2. Check if warmer is plugged in

3. Check if the ON/OFF switch/circuit breaker is turned on

4. Check the fuse on the incoming supply

Check for power at the junction box in the control panel

6. Contact your MAC Medical authorized service representative

Chamber does not heat

1. Is the power turned on?

2. Is the temperature set above chamber ambient temperature?

3. Is the circulation fan operational? Open the door and press in on the door switch

4. Is there voltage on the output terminal of the controller?

5. Is the door(s) closed?

6. Contact your MAC Medical authorized service representative

Over temperature alarm

activated

7. Is the circulating fan operational?

8. Are the contents loaded properly?

9. Has the chamber set temperature been lowered?

10. Temperature of the lower chamber cannot be in excess of +30°F (+1.1°C) above the

upper chamber

11. Contact your MAC Medial authorized service representative

Содержание D Series

















































Результаты поиска

Содержание D Series

Отзывы:

Похожие инструкции для D Series

Бренды по названию

Популярные бренды

Mac Medical D Series, Установка, эксплуатация и обслуживание

Результаты поиска

Содержание D Series

Отзывы:

Похожие инструкции для D Series

Бренды по названию

Популярные бренды