Mac Medical D Series Скачать руководство пользователя страница 20

Страница: 20 / 48

Instruction Manual

MAN-001

www.macmedical.com

Installing and Adjusting Optional Roller basket Shelves

Install the roller basket shelf by first attaching the two roller channels to the cabinet walls.

1. First, insert the top tab of one end of the roller channel into a slot (the roller channel width spans 4 slots). Fig.

15 & Fig. 16.

2. After inserting the top tab , push up slightly on it while snapping in the bottom tab into a slot located 3 slots

below the top slot. (Fig. 17)

Snap in the other end (make sure it is level with the first end) and attach the other roller channel to the

opposite side in the same manner. Be sure both channels are level with each other.

4. Set the 2 sets of rollers of the roller basket into the channel tracks on both sides and slide the shelf in (Fig. 18 -

Fig. 19).

Adjust the Roller Basket Shelf

To adjust the roller basket shelf, slide the shelf out and lift up to clear the rollers from the roller channel track.

Set the shelf aside.

2. Remove the roller channels by pushing up slightly on the top tab of the channel and pull out the channel

from the bottom.

3. Re-install the roller channels in another location using the same installation process described above.
4. After re-installing the roller channels, re-install the shelf by aligning its rollers in the roller channel track and

sliding the shelf in.

Note: For information on basket dimensions and part numbers pertaining to warmer cabinet models, see page

26.

Fig. 20:

Inserting Top Channel Tab

Fig. 21:

Cabinet Wall Slots

Fig. 22:

Inserting Bottom Channel Tab

Fig. 23:

Rollers in Channel Track

Fig. 24: Roller Basket Shelf Installed

Содержание D Series

















































Результаты поиска

Содержание D Series

Отзывы:

Похожие инструкции для D Series

Бренды по названию

Популярные бренды

Mac Medical D Series, Установка, эксплуатация и обслуживание

Результаты поиска

Содержание D Series

Отзывы:

Похожие инструкции для D Series

Бренды по названию

Популярные бренды