Mac Medical D Series Скачать руководство пользователя страница 10

Страница: 10 / 48

Instruction Manual

MAN-001

www.macmedical.com

Warnings and Cautions

The following is a list identifying the various warning and caution icon used in this manual.

Icon Type

Icon

Description

Warnings

(Red triangle with an exclamation point) indicates the potential for

minor to severe injuries up to and including death to personnel.

Cautions

(Yellow triangle with an exclamation point) indicates the potential

minor injury to personnel and damage to equipment.

Note: The exclamation point will not be visible where only

equipment damage is present.

Burn Hazard Warnings

(Yellow triangle with radiating lines) indicates a potential burn injury

to personnel.

Electrical Warnings

(Yellow triangle with a lightning bolt) indicates a possible shock

hazard is present. Severe shock hazards shall be a lightning bolt in a

red triangle.

Explosion Hazard

(Yellow triangle with the explosion icon) indicates the equipment

should not be operated in areas where explosions could occur.

Fire Hazard

(Yellow triangle with the fire icon) indicates the warning cabinet

should not be loaded with materials or liquids that are flammable or

use in the presence of flammable anesthetics or solvents.

The following is a list of safety precautions that must be observed when operating this equipment.

Warning - Injury Hazard

REPAIRS AND ADJUSTMENTS should be attempted only by experienced service representatives. Use of

unqualified persons to work on this equipment could result in personal injury or costly damage.

Warning - Burn Hazard

•  Do NOT use in the presence of flammable anesthetics.
•  Do NOT heat liquids in the presence of flammable solvents.
•  Failure to observe this Warning can result in severe personal injury and even death.

Warning - Burn Hazard

•

Do NOT exceed 150° F (65.56 C) for non-vented closures; (screw caps, crimp seals, plastic pouches, etc.).

Do not exceed pre-sterile solution manufacturer’s temperature requirements.

•

Do NOT raise set temperature to increase rate of heating. Allow approximately 4-6 hours for solutions to

reach desired temperatures.

Содержание D Series

















































Результаты поиска

Содержание D Series

Отзывы:

Похожие инструкции для D Series

Бренды по названию

Популярные бренды

Mac Medical D Series, Установка, эксплуатация и обслуживание

Результаты поиска

Содержание D Series

Отзывы:

Похожие инструкции для D Series

Бренды по названию

Популярные бренды