Mac Medical D Series Скачать руководство пользователя страница 8

Страница: 8 / 48

Instruction Manual

MAN-001

www.macmedical.com

° This product is made from a copper surface that continuously kills bacteria* left behind by dirty

hands, killing more than 99.9% of bacteria* within 2 hours.

Laboratory testing has shown that when cleaned regularly this surface:

° Kills more than 99.9% of bacteria* within 2 hours, and continues to kill 99% of bacteria* even after

repeated contamination.

° Delivers continuous and ongoing antibacterial* action, remaining effective in killing greater than

99.9% of bacteria* within 2 hours.

° Helps inhibit buildup and growth of bacteria* within 2 hours of exposure between routine cleaning

and sanitizing steps.

° Kills greater than 99.9% of Gram-negative and Gram-positive bacteria* within 2 hours of exposure.

° Continuously reduces bacterial* contamination, achieving 99.9% reductin within 2 hours of exposure.

* Laboratory testing shows that, when cleaned regulary, CuVerro surfaces kill greater than 99.9% of the following bacteria

within 2 hours of exposure: Methicillin-Resistant Staphylococcus aureus, Staphylococcus aureus, Enterobacter aerogenes,

Pseudomonas aeruginosa, E. coli O157:H7, and Vancomycin-Resistant Enterococcus faecalis (VRE).

The use of CuVerro® bactericidal copper products is a supplement to and not a substitute for standard infection control

practices; users must continue to follow all current infection control practices, including those practices related to cleaning

and disinfection of environmental surfaces. This surface has been shown to reduce microbial contamination, but it does not

necessarily prevent cross contamination.

CuVerro® is a registered trademark of GBC Metals, LLC and is used with permission.

MAC Medical Warming Cabinet handles are equipped with CuVerro® bactericidal copper surfaces.

EPA Company No. 92702-IL-1

EPA Registration No. 92701

Содержание D Series

















































Результаты поиска

Содержание D Series

Отзывы:

Похожие инструкции для D Series

Бренды по названию

Популярные бренды

Mac Medical D Series, Установка, эксплуатация и обслуживание

Результаты поиска

Содержание D Series

Отзывы:

Похожие инструкции для D Series

Бренды по названию

Популярные бренды