Mac Medical D Series Скачать руководство пользователя страница 12

Страница: 12 / 48

Instruction Manual

MAN-001

www.macmedical.com

Unpacking Instructions

Receiving Requirements
The customer is responsible for making sure the

loading dock at their facility can accommodate a

shipping carton approximately 70” inches (1.778 m)

long and 40” (1.016m) inches wide.
The customer must also provide transportation

equipment (forklift, etc) for a carton weighing

approximately 500 lbs (227 kg).

Inspection

1. Receiving area must meet all State and Local

regulations prior to unpacking.

2. Customer must inspect carton both before and

after unpacking to determine if any items were

damaged during shipping.
A. All damaged items must be listed on the Bill of

Lading.

B. The serial number and model number shown

on the carton label must match the numbers

on the Bill of Lading and the Invoice.

3. Customer is responsible for the proper disposal of

all packing materials. The disposal of these items

must meet all State and Local regulations.

Unpacking the Warming Cabinet

Retain all shipping materials until warming cabinet is

completely unpacked and inspected for damage.
1. Remove metal bands holding the bottom and

top of the shipping carton together.

2. Remove all metal staples holding the top and

bottom of the carton to its sides.

3. Remove the top of the carton.
4.

Remove metal staples making the flaps around

the top edge of the carton.

5. Remove metal staples attaching the sides of the

carton to the bottom of the carton.

6. Remove the sides of the carton by lifting them

straight up from the bottom tray.

7. Lift Warmer straight up from bottom tray of the

shipping carton and remove it.

8. Remove all protective packing material.

Caution:

DO NOT use a box cutter

or any other cutting utensil to remove the

plastic protective wrapping around the

Warming Cabinet. These items can scratch

the protective coating on the stainless steel

allowing the surface to rust.

9. The Warming Cabinet is now ready for use.
10. Discard shipping and packing materials in

compliance with local and state regulations.

11. Warmers, when not in use, must NOT be double-

stacked while in storage. Warmers, while still in

shipping cartons, must not be double-stacked

when not in use.

Fig. 6:

Warming Cabinet in Shipping Container

Содержание D Series

















































Результаты поиска

Содержание D Series

Отзывы:

Похожие инструкции для D Series

Бренды по названию

Популярные бренды

Mac Medical D Series, Установка, эксплуатация и обслуживание

Результаты поиска

Содержание D Series

Отзывы:

Похожие инструкции для D Series

Бренды по названию

Популярные бренды