Mac Medical D Series Скачать руководство пользователя страница 7

Страница: 7 / 48

Instruction Manual

MAN-001

www.macmedical.com

General

Specifications

Cabinet Construction and Material

•

300 Stainless Steel (all panels, header and doors) Double walled construction with insulation. Doors are

double pan stainless steel.

•

Fully insulated to provide uniform heating

•

Optional Glass door are double paned tempered glass framed with aluminum.

•

Doors are fully gasketed and hinged on right side or optionally on the left side.

Factory Presets

• All units are preset to measure temperature in Fahrenheit (unless the unit was specifically ordered to be

preset for Celsius.)

Power Specifications are located on the unit

identification rating tag (see Fig. 4) which is

permanently attached on the inside of the

door or on the back of the upper chamber.

Power Requirements

•

120VAC, 60Hz, Single Phase, 15 AMP,

Ground Fault Interrupter Circuit (GFIC)

protected electrical outlet, or 220 VAC,

60Hz, Single Phase, 7 AMP, GFIC protected

electrical outlet (by others) installed

per local building codes and provides

protective grounding.

•

Cabinets are supplied with a 7 foot (2.3m)

long, 14-3 SJT power cord with a 120V

(NEMA 15P) hospital grade plug. For multi-

chambered units, ON/OFF switches are

supplied for each chamber.

•

All individual electronic components are

Underwriter’s Laboratory (UL) approved

and recognized.

Electrical Specifications by Model

Model #

Description

SWC151822

120V, 2.08 Amp, 50/60Hz, .25 kWh (Avg.), 853 BTU/hr (Avg.)

SWC182424

120V, 2.9 Amp, 50/60 Hz, .23 kWh (Avg.), 785 BTU/hr (Avg.)

SWC182436
SWC242424

120V, 6.3 Amp, 50/60 Hz, .45 kWh (Avg.), 1535 BTU/hr (Avg.)

SWC242436
SWC243024
SWC243036
SWC183024

120V, 5.7 Amp, 50/60 Hz, .45 kWh (Avg.), 1535 BTU/hr (Avg.)

SWC183036
SWC182464

120V, 6.5 Amp, 50/60 Hz, .47 kWh (Avg.), 1604 BTU/hr (Avg.)

SWC182474
SWC183074
SWC242474
SWC243074
SWC242464

120V, 6.5 Amp, 50/60 Hz, .41 kWh (Avg.), 1604 BTU/hr (Avg.)

SWC243064
SWC183064

120V, 6.3 Amp, 50/60 Hz, .41 kWh (Avg.), 1400 BTU/hr (Avg.)

DWC183064T

120V, 8.3 Amp, 50/60 Hz, .60 kWh (Avg.), 2047 BTU/hr (Avg.)

DWC242464T
DWC182464T

120V, 8.9 Amp, 50/60 Hz, .65 kWh (Avg.), 2218 BTU/hr (Avg.)

DWC182474E
DWC182474T
DWC243064T
DWC242474E
DWC242474T
DWC183074T

120V, 8.3 Amp, 50/60 Hz, .82 kWh (Avg.), 2047 BTU/hr (Avg.)

DWC243074T

120V, 12.5 Amp, 50/60 Hz, .90 kWh (Avg.), 3071 BTU/hr (Avg.)

DWC183074E

120V, 11.4 Amp, 50/60 Hz, .82 kWh (Avg.), 2798 BTU/hr (Avg.)

DWC243074E

120V, 12.9 Amp, 50/60 Hz, .90 kWh (Avg.), 3071 BTU/hr (Avg.)

TWC183078
TWC243078

Fig. 4:

Power Specification Label

Содержание D Series

















































Результаты поиска

Содержание D Series

Отзывы:

Похожие инструкции для D Series

Бренды по названию

Популярные бренды

Mac Medical D Series, Установка, эксплуатация и обслуживание

Результаты поиска

Содержание D Series

Отзывы:

Похожие инструкции для D Series

Бренды по названию

Популярные бренды