Mac Medical D Series Скачать руководство пользователя страница 13

Страница: 13 / 48

Instruction Manual

MAN-001

www.macmedical.com

Installing D-Series Warming Cabinets

environmental Conditions

This unit is intended for use in a stable ambient

environment, with an ideal temperature of 72° F

(22.22° C) or less. The unit should never be used

directly next to any appliance that may produce

heat, such as an autoclave.

During Transport and Storage (in original packaging

materials) -

•

Ambient Temperature: -40° - 159°F (-40° - 70°C)

•

Relative Air Pressure: 10% - 100%, including

condensation

•

Air Pressure: 500 hPa (14 inHg - 31.3 inHg)

During Use - for Dry Locations

•

Ambient Temperature: 60° - 85°F (15° - 30°C)

•

Relative Air Moisture: 30% - 60% non-condensing

•

Air Pressure: 700 hPa - 1060 hPa (20.7 inHg - 31.3

inHg)

Installation

Before starting the installation, review the local

electric codes including the Occupational Health

and Safety Act for any requirements pertaining to the

proper installation of this equipment.
Contact your MAC Medical representative for seismic

calculations and tie-down hardware, if applicable.

1. Carefully uncrate the D-Series Warming Cabinet.
2. Inspect for any damage. If there is damage,

please contact MAC Medical, Inc. at (1-877-828-

9975).

3. Check your 120V, 60 Hz, Single Phase 15 AMP

GFIC Protected electrical outlet or 220V, 60 Hz,

Single Phase, 7 AMP GFIC Protected electrical

outlet. Be sure the outlet is safely accessible and

in proper working condition.

4. Plug the 3-prong electrical plug into the 120VAC,

60Hz, 15 AMP, GFIC Protected Outlet or a 220

VAC, 60Hz, Single Phase, 7 AMP GFIC protected

electrical outlet. Make sure the electrical outlet is

safely accessible and in proper working condition.

5. Place Warming Cabinet on a solid, level platform

where external movement will not interfere with

loose contents used by the warmer.

6. Make sure the shelving is correctly located as

desired and level. If not, adjust their height (see

“Adjusting the Shelves” on page 19).

7. Before use, remove any items that have been

stored in the cabinet.

Testing before Using

All warming cabinets have been calibrated and

tested before leaving the factory. There is no need

for the user to do additional testing after installation

prior to use.
After six month of use, it is recommended that the

user test the warming cabinet for temperature

accuracy. See “Semi-Annual Checklist” on page

24.

Содержание D Series

















































Результаты поиска

Содержание D Series

Отзывы:

Похожие инструкции для D Series

Бренды по названию

Популярные бренды

Mac Medical D Series, Установка, эксплуатация и обслуживание

Результаты поиска

Содержание D Series

Отзывы:

Похожие инструкции для D Series

Бренды по названию

Популярные бренды