Mac Medical D Series Скачать руководство пользователя страница 19

Страница: 19 / 48

Instruction Manual

MAN-001

www.macmedical.com

Installing the Shelves

1. Where applicable, turn the power OFF to the

heating chamber that needs a shelf installed in it.
A. Allow the heating chamber to cool. Then

unload any contents.

2. Install the 4 shelf support clips into the desired

location by inserting the top tab into the upper

wall slot of that position (Fig. 12 & Fig. 13). Push

up slightly on the inserted top tab and push the

bottom half of the clip in until the bottom tab

snaps into the lower slot.

3. Count the mounting locations at each corner of

the chamber to be sure that the shelf will be level

and install the remaining support clips.

4. Install the shelf with the notches on the bottom of

the shelf aligned with the shelf supports (Fig. 13 &

Fig. 14).

5. Pull outward on the shelf to insure it is locked

properly on the supports.

Adjusting the Shelves

1. Turn the power OFF to the heating chamber that

needs its shelf adjusted.

A. Allow the chamber to cool. Then unload the

contents.

2. Remove the shelf and determine its new position.
3. Remove the four (4 per shelf) shelf supports clips

by tilting the clip upwards and lifting out.

4. Install the shelf support into the new location by

inserting the top tab into the upper slot of the new

position. Push up slightly on the inserted top tab

and push the bottom half of the clip in until the

bottom tab snaps into the lower slot..

5. Count the mounting locations at each corner of

the chamber to be sure that the shelf will be level

and install the remaining supports.

6. Re-install the shelf with the notches on the bottom

of the shelf aligned with the shelf supports.

7. Pull outward on the shelf to insure it is locked

properly on the supports.

NOTE: Shelves are notched at each

corner to rest on 4 shelf support clips

that are inserted into the cabinet wall

slots (Figure 14).

Fig. 16:

Shelf Support

Fig. 17:

Shelf Support showing tabs

Wall Slots

Fig. 18:

Support Clip Fitted in Notch

Fig. 19:

Shelf Notch

Содержание D Series

















































Результаты поиска

Содержание D Series

Отзывы:

Похожие инструкции для D Series

Бренды по названию

Популярные бренды

Mac Medical D Series, Установка, эксплуатация и обслуживание

Результаты поиска

Содержание D Series

Отзывы:

Похожие инструкции для D Series

Бренды по названию

Популярные бренды