Lucent 23N12 Скачать руководство пользователя страница 66 | Manualshive

Страница: 66 / 176

Lucent 23N12 Скачать руководство пользователя страница 66

Chapter 3 Configuring the OC-3 Mode Ports and Channels Using the Console

Configuring J1 Trace

3-36

255-700-714R11.0

PacketStar

®

PSAX 1-Port Channelized OC-3/STM-1 CES Module User Guide

, Issue 1

Release 11.0.0

2

After applying the

Port Configuration

command in the OC-3 SM Port

Configuration window (see Figure 3-8), select the

Configure STS1 Vir-

tual Port 1

.

The Channelized OC-3 SM STS1 Port Configuration window is displayed
(see Figure 3-17). Table 3-6 describes the commands on the window.
Table 3-7 describes the fields on the window.

3

Remain on the same window, select the

J1 Trace Configuration

com-

mand.

The Higher Order Path Trace - J1 Byte Configuration window is dis-
played (see Figure 3-18). Table 3-17 describes the commands on this
window. Table 3-18 describes the configurable fields on this window.

4

Select the values for the fields on the window in Figure 3-18 from
Table 3-18.

5

Select the

Apply Configuration

command and press Enter.

End

Table 3-16. Channelized OC-3 or STM-1 CES Port Configuration Window Field Descriptions

Field Name

Field Value

Description

Loopback Config Default:

NoLoop

Range: N/A

Format: Predefined

Specifies whether and what kind of loopback configuration
is used on the signal on this connection.

NoLoop

Indicates that no loopback is to be done on the signal.

LocalLoop

Indicates that the received signal at this interface enters
through the backplane, is looped through the device, and
exits through the backplane.

LineLoop

Indicates that received signal at this interface does not pass
through the device but is looped back out through the exter-
nal port.

Transmit Clock

Default:

LocalTim-

ing

Range: N/A

Format: Predefined

Indicates what type of synchronization is used by the inter-
face to maintain proper data flow through the PSAX system
and the remote devices connected to the system.

LocalTiming

Selects a synchronization source (CompositeClock, T1BITS,
E1ETSI, CompositeClockDS0A, Freerun, or LineTiming) that
is provided through the Stratum 3–4 module. For GR-303
configuration, select this default.

LoopTiming

This value is currently not supported.

«
...
64
65
66
67
68
...
»

Содержание 23N12

















































































































































































Отзывы:

Нет отзывов