background image

3 - 55

Down speed control knob

Fast

Slow & Lock

Down speed control knob (Roll-bar 

type)

It is use to adjust the down speed of the 3-point 
linkage. Turn the down-speed control knob to 
the right direction for slower down speed, and to 
the left direction for faster down speed. 

If turning the knob right direction fully, the 
implement will be fixed and even if lowering 
down the position control lever, the implement 
does not let down.
- Tiller: Slow in down speed
- Plough: Fast in down speed

When working in hard ground, slow down the 
down speed to avoid bounding of the implement.

When driving on the road, replacing tiller blades or removing grass around the tiller 

blades, turn the down-speed control knob clockwise slightly to lock.

The knob rotates about two revolutions. Do not over-tighten the knob. It may cause 

damage to the control valve and connection parts.

Warning

Содержание MT342









































































































































































































































































Отзывы: