LS tractor MT342 Скачать руководство пользователя страница 238

Страница: 238 / 264

5 - 58

(5) Tail/brake light bulb and turn signal light bulb- Replace

①

Tail/brake light bulb and rear turn

signal light bulb replacement

1. Remove the harness connector.

2. Unscrew the locking screws

①

②

with retaining

the rear lamp assembly.

3. Turn the socket of the brake light

③

or turn

signal light

④

counter-clockwise to remove the

socket from the housing.

4. Push in on the tail/brake light bulb or turn signal

light bulb and rotate counter-clockwise in the
socket to remove the old bulb.

5. Insert a new bulb into the socket and turn the

bulb in a clockwise direction until tightened.

6. Install the socket and rear lamp assembly.

NOTE: For about bulb specification, refer to the

chapter 5-6-(4) in this manual.

Roll-bar

Cabin

Roll-bar

Cabin

Содержание MT342









































































































































































































































































Результаты поиска

Содержание MT342

Отзывы:

Похожие инструкции для MT342

Бренды по названию

Популярные бренды

LS tractor MT342, Руководство оператора

Результаты поиска

Содержание MT342

Отзывы:

Похожие инструкции для MT342

Бренды по названию

Популярные бренды