LS tractor MT342 Скачать руководство пользователя страница 202 | Manualshive

Страница: 202 / 264

background image

5 - 22

(3) Instrument panel & Indicators



Check if the indicators are normally turned on/off
before starting engine or while operating
frequently and periodically.



If the

engine oil pressure indicator

and

battery charging indicator

are turned on while

the engine is running, stop the engine
immediately and check the engine lubrication
system and battery charging system. If possible,
contact your authorized dealer for check.



You must drain water in the fuel filter when the
fuel filter warning indicator lights. Refer to the
chapter 5-5-(1) in this manual.



For further information about indicators, refer to

the chapter 3-1-(1), “Instrument panel” in this

manual.

(2) Fuel tank

①

Fuel and Fuel tank Capacity:



See chapter 5-3, “Lubricants and Capacity” or

the last page in this manual.



If contaminants such as dust or water are mixed

with the fuel, it can cause serious damage to the
engine. The fuel storage facility must be
equipped as shown in the right figure.
If possible, fill the tank with fuel at a gas station.

②

Using Diesel for winter



General diesel fuel tends to generate paraffin

dregs in cold weather which may cause a bad
engine start. Thus, it is recommended to use
diesel for winter in cold weather.

Drum

Impurities

③

Checking Fuel level and filling the tank



Check the fuel gauge of the tractor fuel tank and if it’s not sufficient, fill the fuel tank with diesel fuel.

For further information about diesel fuel, see chapter 5-1-(3), 5-1-(4), 5-1-(5) in this manual.

▶

After finishing work, fill the fuel tank fully. As the temperature drops down at night,

the humidity in the fuel tank is condensed, and may be mixed with the fuel.

Notice

Battery charging

indicator

Engine oil pressure

indicator

Fuel filter

warning indicator

«
...
200
201
202
203
204
...
»

Содержание MT342









































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для MT342

UpFront STS 12 Combo

Бренд: Hagie Страницы: 149

Бренд: Yanmar Страницы: 202

Бренд: Siemens Страницы: 96

Бренд: Zanussi Страницы: 104

Бренд: Poulan Pro Страницы: 52

Бренд: Amica Страницы: 60

Бренд: Amica Страницы: 68

Бренд: New Holland Страницы: 2

Бренд: New Holland Страницы: 9

Бренд: New Holland Страницы: 41

Бренд: Winton Страницы: 12

Бренд: McCulloch Страницы: 108

Tractor TURBOMIX MTXH

Бренд: Bauer Страницы: 42

Бренд: Cub Cadet Страницы: 48

Бренд: Tarmo Страницы: 27

Бренд: Nortrac Страницы: 47

Бренд: Maytag Страницы: 16

Бренд: Dixon Страницы: 30

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды