LS tractor MT342 Скачать руководство пользователя страница 245

Страница: 245 / 264

5 - 65

System

Faults

Possible causes

Solutions

Steering

System

Hydraulic steering
system does not work.

▲

Pump worn or part damaged

▲

Steering unit damaged or worn

▲

Oil leakage by steering

cylinder piston seal damaged or
worn

▲

Oil leakage by pipe damage

▲

Repair or replace

▲

Repair or replace

▲

Repair

▲

Repair or replace

Hard to operate the
steering wheel.

▲

Steering unit

- Steering unit spline and column

spline is not aligned

- Spool and sleeve damaged by

foreign material

- Excessive tightening torque of

end cap bolt

▲

Pump

- Low speed

- Wearing or failure

▲

Relief valve

- Valve spool clogged

- Setting pressure too low

▲

- Check mounted condition of

steering unit and column

- Replace

- Apply regular torque

▲

- Adjust RPM or Repair

- Repair or replace

▲

- Repair or replace

- Reset or adjust

Cylinder does not work
smoothly as steering
wheel movement

▲

Air in steering line if not used

for a long time

▲

Air in suction pipe

▲

Piston seal damaged

▲

Bleed air

▲

Repair

▲

Replace

Steering wheel turns to
the opposite direction.

▲

bad assembly of steering gear

▲

bad assembly of steering hose

▲

Repair

▲

Repair

Oil leakage of steering
pump, steering unit,
cylinder and fittings

▲

Seal damaged

▲

Replace seal

Abnormal noise

▲

Lack of oil

▲

Exceeding resistance of

suction line

▲

Air in system

▲

Aid oil

▲

Replace filter or repair

pump

▲

Bleed air

Содержание MT342









































































































































































































































































Результаты поиска

Содержание MT342

Отзывы:

LS tractor MT342, Руководство оператора, Страница: 245 / 264

Результаты поиска

Содержание MT342

Отзывы: