LS tractor MT342 Скачать руководство пользователя страница 124 | Manualshive

Страница: 124 / 264

LS tractor MT342 Скачать руководство пользователя страница 124

3 - 48

GSP lever

GSP

Independent PTO

(13) Ground Speed PTO (GSP)

lever (if fitted)



This lever is used to select the ground speed
PTO(GSP) or independent PTO.



The ground speed PTO rotates proportionally
according to the rear wheel speed. The
independent PTO rotates proportionally
according to the engine speed regardless of the
rear wheel speed.



If you pull the lever backward, the ground speed
PTO (GSP) is engaged.



If you push the lever forward fully, the ground
speed PTO (GSP) is disengaged and
independent PTO is available.



Before operating the GSP lever,

- press a clutch pedal, brake pedals, and stop

the tractor completely.

- put the PTO switch in OFF position and stop

the PTO shaft completely.

Middle PTO lever

ON

(12) Middle PTO lever (if fitted)



It is used to engage/disengage the middle PTO
gear.



Before operating the middle PTO lever, put PTO
switch to “OFF” position and stop the PTO shaft
completely.



Pull the middle PTO lever up to engage the
middle PTO gear.



For further information about the PTO shaft, see

chapter 4-5-(2) in this manual.

«
...
122
123
124
125
126
...
»

Содержание MT342









































































































































































































































































Отзывы:

Нет отзывов