LS tractor MT342 Скачать руководство пользователя страница 94 | Manualshive

Страница: 94 / 264

background image

3 - 18

⑤

Regeneration mode

▶

Fire hazard!

During the Diesel Particulate Filter(DPF) regeneration process, the exhaust stack
and fixed hood area becomes extremely hot. Park the machine outside and away
from combustible or highly flammable material.
Failure to comply could result in death or serious injury.

Warning



In this mode, the operator does not need to take

any actions, the system is activated
automatically by the engine electronic controller.

NOTE : The regeneration is the normal operating

mode.



The regeneration will be activated by ECU ;

-

When soot’s rate reaches

100% or more

.

-

When the engine is

warmed up enough.

-

When the

DPF switch is not pressed to the

Inhibited regeneration mode.

NOTE : Regeneration will be lasted for

approximately 15 to 25 minutes.

▶

If engine is turned off during the regeneration, soot will not be completely burned

and may increase fuel consumption. KEY-OFF during regeneration mode is not
recommendable because too short operation won’t finish regeneration mode, So,
we recommend to users to operate until all indicator lights are turned off without Key
switch OFF.

NOTICE

1

2



If pressing and holding the upper part of the DPF switch over 3 minutes, the regeneration can be

activated manually. In this case, if the soot’s rate is reached over minimum 30%, the regeneration
will be activated.



During the regeneration, the DPF regeneration indicator(1) and DPF temperature indicator(2) will be

turned on.



In case of turning off the engine while the regeneration is processing, the regeneration is to resume

again when restarting the engine.

«
...
92
93
94
95
96
...
»

Содержание MT342









































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для MT342

Бренд: LS tractor Страницы: 144

Бренд: Daedong Страницы: 256

Бренд: KitchenAid Страницы: 7

Бренд: KitchenAid Страницы: 16

Бренд: KitchenAid Страницы: 19

Бренд: KitchenAid Страницы: 19

Бренд: KitchenAid Страницы: 3

Бренд: KitchenAid Страницы: 16

Бренд: KitchenAid Страницы: 16

Бренд: KitchenAid Страницы: 1

3000 STAR Series

Бренд: GOLDONI Страницы: 173

Бренд: satoh Страницы: 72

Бренд: Winton Страницы: 40

RK37 Hydrostatic

Бренд: Rural King Страницы: 182

Бренд: FENDT Страницы: 51

Craftsman 944.600940

Бренд: Sears Страницы: 60

OPTIMAL UPX Series

Бренд: Trejon Страницы: 44

Бренд: Poulan Pro Страницы: 30

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды