LS tractor MT342 Скачать руководство пользователя страница 122

Страница: 122 / 264

3 - 46

(9) Range gear shift lever

(Mechanical)



Four speed gear shift and neutral position is

available.



Before operating the range gear shift lever, press

down the clutch pedal, brake pedals, and stop
the tractor completely.

Range gear
shift lever

Mechanical

Notice

▶

Operate the range gear shift lever by correct “H” pattern. If operated diagonally, it

may cause a failure.

(8) Work light switch



The rear work light has a switch on its back. To

turn on/off the rear work light, operate the switch
as shown in the right figure.

OFF

▶

When driving on the road at night, do not let the rear work light stay ON. It may

cause a disturbance to the driver of the following car.

Caution

Содержание MT342









































































































































































































































































Результаты поиска

Содержание MT342

Отзывы:

Похожие инструкции для MT342

Бренды по названию

Популярные бренды

LS tractor MT342, Руководство оператора

Результаты поиска

Содержание MT342

Отзывы:

Похожие инструкции для MT342

Бренды по названию

Популярные бренды