LS tractor MT342 Скачать руководство пользователя страница 75 | Manualshive

Страница: 75 / 264

background image

2 - 13

②

Cabin

Cabin



This Roll-Over Protective Structure, Cabin is an
integrated and certified structure for driver’s
safety. This structure will reduce the risk of
serious injury or death when being over-turned.



DO NOT remove, modify or repair the cabin
arbitrary. Any damage of fire, corrosion, welding,
bending, drilling, grinding and cutting of any part
of the cabin, it can weaken the protective
structure.



If the cabin mounting bolts or other inter-
connecting parts are loosened or removed for
any reason, make sure that all the parts
reinstalled correctly before operating the tractor.

Warning

Roll-over hazard!

Failure to comply could result in death or serious injury.

▶

Do not modify or remove the Roll-Over Protective Structure(ROPS) arbitrarily for

safety. Unless the ROPS is installed correctly, it may cause a serious accident or
death when being overturned.

▶

Be sure to stand up the Roll-Over Protective Structure(ROPS) and check the bolts,

pins and nuts correctly kept in place.

▶

Always wear the seat belt when operating the vehicle in the cabin.

▶

Do not connect chains or ropes to the ROPS for pulling purposes, as the vehicle

could tip over.

▶

When driving through door openings or under low overhead objects, make sure

there is sufficient clearance for the ROPS.

▶

Do not step on the fender for the maintenance of cabin roof.

«
...
73
74
75
76
77
...
»

Содержание MT342









































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для MT342

Бренд: Land Pride Страницы: 38

Бренд: Kioti Страницы: 170

Бренд: Case Страницы: 96

Бренд: Kioti Страницы: 150

Бренд: Kalmar Страницы: 262

Бренд: New Holland Страницы: 41

Бренд: Troy-Bilt Страницы: 113

MEGA MEZZO HI-TEC

Бренд: Valtra Страницы: 11

Бренд: Zenoah Страницы: 96

Бренд: Mahindra Страницы: 18

Бренд: Kioti Страницы: 108

Бренд: Cub Cadet Страницы: 2

Бренд: Cub Cadet Страницы: 60

Бренд: Tiger Страницы: 202

BENGAL JD6110-20M/R MY20

Бренд: Tiger Страницы: 223

BENGAL JD6110-30M/R T4F

Бренд: Tiger Страницы: 226

WILDKAT JD6105-25E T4F

Бренд: Tiger Страницы: 240

Бренд: Tiger Страницы: 236

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды