LS tractor MT342 Скачать руководство пользователя страница 255

Страница: 255 / 264

6 - 7

No.

Failures

Cause

Actions

The compressor does not turn or
it is hard to revolve.

Belt loosened.

Adjust the belt tension.

Temperature switch or

pressure switch is ON.

Check refrigerant

amount.

Coil of magnet clutch was

shorted or cut off.

Contact the dealer.

Compressor failure.

Contact the dealer.

Wiring cut off or poor
connection such as ground.

Check and repair.

The warm airflow does not blow.

The amount of warm water
is small.

Check and add the

engine coolant.

Heater line is clogged or

distorted.

Check and repair.

Poor operation of the

thermostat of engine

coolant.

Repair or replace.

Содержание MT342









































































































































































































































































Результаты поиска

Содержание MT342

Отзывы:

Похожие инструкции для MT342

Бренды по названию

Популярные бренды

LS tractor MT342, Руководство оператора

Результаты поиска

Содержание MT342

Отзывы:

Похожие инструкции для MT342

Бренды по названию

Популярные бренды