LS tractor MT342 Скачать руководство пользователя страница 212

Страница: 212 / 264

5 - 32

(1) Lubricating grease nipple



Front axle holders. (Front/Rear)



Steering tie-rod. (Both side)



3-point linkage.

5-7. Every 50 hour check

Grease nipples

(2) Cleaning of Radiator and Radiator screen



See chapter 5-6-(7) in this manual (See page 5-25).

1.Wipe dirt from fittings before greasing.

2.Use a grease gun containing clean high grade of

grease.

For grease specification, see chapter 5-3,

“Lubricants and Capacity” or the last page in this

manual.

3.Pump fresh grease into fitting to adequately

lubricate the component and force out any
contamination from the grease passage.

4.Wipe off excess grease.

Grease nipple
(Both side)

Grease nipple

Содержание MT342









































































































































































































































































Результаты поиска

Содержание MT342

Отзывы:

LS tractor MT342, Руководство оператора, Страница: 212 / 264

Результаты поиска

Содержание MT342

Отзывы: