LRS LineShare PRO Скачать руководство пользователя страница 40 | Manualshive

Страница: 40 / 43

LRS LineShare PRO Скачать руководство пользователя страница 40

DRS Assignment

The DRS Assignment operates in either the Automatic mode or the Semi-Automatic mode.

This feature designates where the LineShare Pro 104 will transfer a call using the Distinctive Ring service. It
has the ability to recognize four different ring signals:

0- - - no ring assigned

1- - - standard ring

2- - - two-burst ring

3- - - three-burst ring (short-short-long)

(Short short short)

(Long long long)

(Long short short)

(Short long long)

4- - - three-burst ring (short-long-short)

(Long short long)

(Long long short)

The LineShare Pro 104 looks for a 4-digit entry to set the port designations for the individual rings. The first
digit represents port P1, the second digit represents port P2, the third digit represents port P3, and the fourth
digit represents port P4. The LineShare Pro 104 cannot be set to transfer any ring signal to more than one
port.

The factory setting is # * (three beeps) 8 0 1 2 3 4 * which transfers a standard ring to port P1, a two burst
ring to port P2, a three burst ring (above) to port P3, and a three burst ring (above) to port P4.

To change this feature, perform the following steps:

1. Take the phone in port P2 off-hook

2. Press # * (three beeps) 8 0 _ _ _ _ * (three beeps) * (one beep) (blank spaces represent the new

DRS Assignment)

3. Hang up the phone

NOTE:

If a ring burst is not assigned, the LineShare Pro 104 will not respond to the incoming call des-
ignated to that phone number.

Each ring burst can be assigned to 1 port. If you attempt to assign a ring burst to more than 1 port, the Line-
Share Pro 104 will give an error tone.

Reset to Factory Settings

To reset all features and feature settings to their original factory settings, perform the following steps:

1. Take the phone in port P2 off-hook

2. Press # * (three beeps) 9 9 9 * (three beeps) * (one beep)

3. Hang up the phone

NOTE:

This does not reset the Remote Security Access Code. Refer to the Remote Security Access
Code section for more information.

Long Range Systems

39

Line Share PRO

«
...
38
39
40
41
42
...
»

Содержание LineShare PRO












































Отзывы:

Нет отзывов