LRS LineShare PRO Скачать руководство пользователя страница 30 | Manualshive

Страница: 30 / 43

LRS LineShare PRO Скачать руководство пользователя страница 30

To turn this feature ON:

1. Take the phone in port P2 off-hook

2. Press # * (three beeps) 1 1 0 * (three beeps) * (one beep)

3. Hang up the phone

Modem Tone Detection – 1300 Hz

This feature allows the LineShare Pro 104 to detect a 1300Hz tone typically from a modem. When set to ON,
1300 Hz tones are detected. When set to OFF, 1300 Hz tones are ignored.

Operation in the Automatic mode and Semi-Automatic mode varies as follows:

Automatic Mode

After the LineShare Pro 104 answers a call, the telephone line is monitored for a 1300 Hz tone and the call is
transferred to the designated port if detected. The port is determined by the Port Tone Assignment parame-
ter.

Semi-Automatic Mode

After a call is answered, the LineShare Pro 104 monitors the telephone line for a 1300 Hz tone and the call is
transferred to the designated port if detected. The port is determined by the Port Tone Assignment parame-
ter.

In both the Automatic and Semi-Automatic modes, the LineShare Pro 104 only monitors the line for tones
for the time specified by the Single Tone Detection Timer. This timer has a factory setting of 10 seconds.

The factory setting for Modem Calling Tone Detection is ON.

To turn this feature OFF:

1. Take the phone in port P2 off-hook

2. Press # * (three beeps) 0 1 1 * (three beeps) * (one beep)

3. Hang up the phone

To turn this feature ON:

1. Take the phone in port P2 off-hook

2. Press # * (three beeps) 1 1 1 * (three beeps) * (one beep)

3. Hang up the phone

Distinctive Ring Service (DRS) Detection

This feature allows the LineShare Pro 104 to detect the various ring signal patterns from the phone com-
pany that are associated with DRS. It works with DRS Assignment to automatically transfer calls to any port
on the LineShare Pro 104 without requiring single frequency tones or transfer codes.

The factory setting for Distinctive Ring Service Detection is OFF.

To turn this feature ON:

1. Take the phone in port P2 off-hook

2. Press # * (three beeps) 1 1 3 * (three beeps) * (one beep)

Long Range Systems

29

Line Share PRO

«
...
28
29
30
31
32
...
»

Содержание LineShare PRO












































Отзывы:

Нет отзывов