LRS LineShare PRO Скачать руководство пользователя страница 29 | Manualshive

Страница: 29 / 43

LRS LineShare PRO Скачать руководство пользователя страница 29

Semi-Automatic Mode

The Single Tone Detection Timer begins when the call is answered. Once the call is answered, the LineShare
Pro 104 will monitor the telephone line and transfer calls when a single frequency tone is detected. After the
timer expires, transfers will require tone access codes.

The factory setting for Single Tone Detection is ON.

To turn this feature OFF:

1. Take the phone in port P2 off-hook

2. Press # * (three beeps) 0 9 * (three beeps) * (one beep)

3. Hang up the phone

To turn this feature ON:

1. Take the phone in port P2 off-hook

2. Press # * (three beeps) 1 9 * (three beeps) * (one beep)

3. Hang up the phone

NOTE:

This feature supersedes the following features: Fax CNG Detection, Modem Calling Tone De-
tection. If Single Tone Detection is turned OFF, these features will not operate even if they are
programmed ON.

Fax CNG (Calling) Tone Detection

This feature allows the LineShare Pro 104 to detect the 1100 Hz CNG tone typically from a FAX machine.
When set to ON, 1100 Hz tones are detected. When set to OFF, 1100 Hz tones are ignored.

Operation in the Automatic mode and Semi-Automatic mode varies as follows:

Automatic Mode

After the LineShare Pro 104 answers a call, the telephone line is monitored for the CNG tone and the call is
transferred to the designated port if detected. The port is determined by the Port Tone Assignment parame-
ter.

Semi-Automatic Mode

After a call is answered, the LineShare Pro 104 monitors the telephone line for the CNG tone and the call is
transferred to the designated port if detected. The port is determined by the Port Tone Assignment parame-
ter.

In both the Automatic and Semi-Automatic modes, the LineShare Pro 104 only monitors the line for tones
for the time specified by the Single Tone Detection Timer. This timer has a factory setting of 10 seconds.

The factory setting for Fax CNG Tone Detection is ON.

To turn this feature OFF:

1. Take the phone in port P2 off-hook

2. Press # * (three beeps) 0 1 0 * (three beeps) * (one beep)

3. Hang up the phone

Long Range Systems

28

Line Share PRO

«
...
27
28
29
30
31
...
»

Содержание LineShare PRO












































Отзывы:

Нет отзывов