LRS LineShare PRO Скачать руководство пользователя страница 33 | Manualshive

Страница: 33 / 43

LRS LineShare PRO Скачать руководство пользователя страница 33

To turn this feature OFF:

1. Take the phone in port P2 off-hook

2. Press # * (three beeps) 0 1 8 * (three beeps) * (one beep)

3. Hang up the phone

Also see the Caller ID Pass Thru section.

Operating Mode

The Operating mode can be set in either the Automatic mode or the Semi-Automatic mode as previously de-
scribed.

The factory setting is for operation in the Automatic mode

To set the LineShare Pro 104 for Semi-Automatic mode, perform the following steps:

1. Take the phone in port P2 off-hook

2. Press # * (three beeps) 2 1 * (three beeps) * (one beep)

3. Hang up the phone

To set the LineShare Pro 104 for Automatic mode, perform the following steps:

1. Take the phone in port P2 off-hook

2. Press # * (three beeps) 2 0 * (three beeps) * (one beep)

3. Hang up the phone

Port Tone Assignment

This feature designates where the LineShare Pro 104 will transfer a call that produces the following identi-
fying tones:

• 1100Hz Fax CNG tone (if turned ON)

• 1300Hz modem calling tone (if turned ON)

The tones can be set to transfer automatically (depending on operating mode) to any port on the LineShare
Pro 104.

The LineShare Pro 104 looks for a 4-digit code to set the port designations for receiving tone transfers. The
first digit represents port P1, the second digit represents port P2, the third digit represents port P3, the fourth
digit represents port P4. The LineShare Pro 104 cannot be set to transfer any tone to more than one port.

Following are the digits that represent the tones for setting port designations:

0 No tone assigned

1 1100Hz CNG

2 1300Hz modem calling tone

3 1100Hz & CNG 1300Hz modem calling tone

The factory setting for Port Tone Assignment is 0 1 2 0. (P1 = not assigned, P2 = 1100Hz, P3 = 1300Hz, P4 =
not assigned)

Long Range Systems

32

Line Share PRO

«
...
31
32
33
34
35
...
»

Содержание LineShare PRO












































Отзывы:

Нет отзывов