LRS LineShare PRO Скачать руководство пользователя страница 34 | Manualshive

Страница: 34 / 43

LRS LineShare PRO Скачать руководство пользователя страница 34

To change this feature, perform the following steps:

1. Take the phone in port P2 off-hook

2. Press # * (three beeps) 3 0 _ _ _ _ * (three beeps) * (one beep) (blank spaces represent selection

of tones)

3. Hang up the phone

Emergency Call Override

This feature allows the Primary port to interrupt a call in process on another port and operates in either the
Automatic mode or the Semi-Automatic mode.

Emergency Call Override is capable of operating with the phone company's three-way calling service (Emer-
gency Call Override Selection).

Operation of this feature is provided through the Primary port, and can be set for automatic or manual op-
eration.

Automatic Operation

When a call is in process on a port and a phone connected to the Primary port goes off-hook, the LineShare
Pro 104 will automatically release the line as described in "Using the LineShare Pro 104."

Manual Operation

When a call is in process on a port while a phone connected to the Primary port goes off-hook and the # key
is pressed and released, the LineShare Pro 104 will automatically release the line as described in "Using the
LineShare Pro 104."

The factory setting for Emergency Call Override is OFF [# * (three beeps) 3 1 0 * (three beeps) * (one beep) ].

To set the LineShare Pro 104 for Automatic Emergency Call Override, perform the following steps:

1. Take the phone in port P2 off-hook

2. Press # * (three beeps) 3 1 2 * (three beeps) * (one beep)

3. Hang up the phone

To set the LineShare Pro 104 for Manual Emergency Call Override, perform the following steps:

1. Take the phone in port P2 off-hook

2. Press # * (three beeps) 3 1 1 * (three beeps) * (one beep)

3. Hang up the phone

Rings to Answer Call

This feature only applies to the Automatic mode.

This feature determines how many times an incoming call rings before it is answered by the LineShare Pro
104. To configure the LineShare Pro 104 to answer and transfer calls as quickly as possible, the factory set-
ting is 1 ring, Under normal circumstances, it is not necessary to change this setting. The range of this set-
ting is 1 to 30 rings.

Long Range Systems

33

Line Share PRO

«
...
32
33
34
35
36
...
»

Содержание LineShare PRO












































Отзывы:

Нет отзывов