LRS LineShare PRO Скачать руководство пользователя страница 36 | Manualshive

Страница: 36 / 43

LRS LineShare PRO Скачать руководство пользователя страница 36

Rings to Port P4

This feature determines the number of rings that the LineShare Pro 104 provides to port P4 with a range of
0-30 rings and operates in either the Automatic mode or the Semi-Automatic mode.

The factory setting for the Rings to Port P4 is 6 rings.

To change this feature, perform the following steps:

1. Take the phone in port P2 off-hook

2. Press # * (three beeps) 4 4 _ _ * (three beeps) * (one beep) (blank spaces represent the new Rings

to Port P4)

3. Hang up the phone

Primary Port Transfer Timer

This feature designates the timing parameters for operation of the Automatic Primary Port Transfer. It is de-
signed to accommodate the timing parameters of fax machines that do not produce CNG tones.

When using the Automatic Primary Port Transfer feature, set this feature to 10 seconds longer than the out-
going announcement message. If the outgoing announcement message is 10 seconds, set this timer to 20
seconds. This will allow adequate time for non-CNG faxes to reach the fax machine, yet allow callers to
leave messages on the answering machine without transferring to the Secondary port when the call is com-
plete (if the message is longer than 10 seconds).

This feature has a range of 0-99 seconds. If 0 or 00 is entered, the Automatic Primary Port Transfer will al-
ways transfer calls to the Secondary port regardless of time on the line.

The factory setting for the Primary Port Transfer Timer is 30 seconds. To change this feature, perform the following steps:

1. Take the phone in port P2 off-hook

2. Press # * (three beeps) 50_ _ * (three beeps) * (one beep) (Blank keys represent new Primary Port

Transfer Timer setting)

3. Hang up the phone

Ring Reduction Reset Timer

This feature designates the timing parameters for operation of Automatic Ring Reduction and Automatic
Ring Reduction Reset. It is activated when the Automatic No Answer Transfer transfers a call to the Sec-
ondary Port Selection, and the Automatic Ring Reduction reduces the Rings Available to Port P1 (Primary port)
to 2 rings.

When this feature is activated, the LineShare Pro 104 monitors all ports for activity. If there is no activity for
10 minutes, the Automatic Ring Reduction Reset will restore the previous number of rings to the Primary port.

This feature has a range of 1-60 minutes. The Rings to Port P1 (Primary port) can be reset manually as pre-
viously described.

The factory setting for the Ring Reduction Reset Timer is 10 minutes. To change this feature, perform the following steps:

1. Take the phone in port P2 off-hook

2. Press # * (three beeps) 51 _ _ * (three beeps) * (one beep) (Blank spaces represent new Ring Re-

duction Reset Timer setting)

3. Hang up the phone

Long Range Systems

35

Line Share PRO

«
...
34
35
36
37
38
...
»

Содержание LineShare PRO












































Отзывы:

Нет отзывов