manualshive.com logo in svg

LRS LineShare PRO, Руководство оператора, Страница: 27 / 43

Поделиться
Скачать
LRS LineShare PRO Скачать руководство пользователя страница 27

On-Line Extension Interruption Protection 

This feature allows the LineShare Pro 104 to detect when an extension phone (not connected to the LineShare
Pro 104) is using the telephone line.  Once the extension phone is on the line, any device connected to the
LineShare Pro 104 cannot access the phone line. The device simply receives a busy signal until the extension
phone has disconnected from the call.

NOTE:

Phones or data devices connected directly to the LineShare Pro 104 do not require this feature
as the LineShare Pro 104 always maintains exclusion between ports.  This means only one de-
vice port of the LineShare Pro 104 may access the telephone at one time.

If On-Line Extension Protection is turned OFF, a device connected to another port of the LineShare Pro 104
will interrupt or barge-in on a call from any extension phone.

The factory setting for On-Line Extension Protection is ON.

To turn this feature OFF:

1. Take the phone in port P2 off-hook

2. Press # * (three beeps) 0 5 *  (three beeps) * (one beep) 

3. Hang up the phone

To turn this feature ON:

1. Take the phone in port P2 off-hook

2. Press # * (three beeps) 1 5 *  (three beeps) * (one beep) 

3. Hang up the phone

Answer Any Port

For an incoming call, the Answer Any Port feature permits any port that is not ringing to answer the call. Once
the call is answered, the LineShare Pro 104 listens for tone access codes to transfer the call to another port.
In the Automatic mode, if Extension Detection is set to be ON, this feature is automatically turned on.

Conditions that allow the Answer Any Port feature to operate:

1. Any time between ring signals to the Primary port

2. After a No Answer Transfer occurs

3. When Distinctive Ring Service Detection is activated

Conditions that restrict the Answer Any Port feature:

1. Automatic Primary Port Transfer

2. Single frequency tone transfer

3. Tone Access code transfer 

In the Semi-Automatic mode, Single Tone Detection will be activated when a device answers a call.

The factory setting for the Answer Any Port feature is OFF.

To turn this feature ON:

1. Take the phone in port P2 off-hook

2. Press # * (three beeps) 1 6 *  (three beeps) * (one beep) 

Long Range Systems

26

Line Share PRO

Содержание LineShare PRO












































Отзывы:

Нет отзывов