LRS LineShare PRO Скачать руководство пользователя страница 28 | Manualshive

Страница: 28 / 43

LRS LineShare PRO Скачать руководство пользователя страница 28

3. Hang up the phone

To turn this feature OFF:

1. Take the phone in port P2 off-hook

2. Press # * (three beeps) 0 6 * (three beeps) * (one beep)

3. Hang up the phone

Pound Key Transfer Required

This feature allows the LineShare Pro 104 to require the # key be entered before the transfer code for a port
or for entering the remote programming mode using the Security Access Code.

With this feature turned ON, the # is required to be entered before the transfer code to initiate the transfer.
(For example # 3 3). If an incorrect access code is entered press # and re-enter the transfer code to complete
a transfer.

If this feature is turned OFF, only the transfer code for the port is required to initiate the transfer. (For exam-
ple 3 3 ). If an incorrect access code is entered, the caller can wait 5 seconds or press # and re-enter the
transfer code to complete a transfer.

The factory setting for the Pound Key Transfer Required feature is ON.

To turn this feature OFF:

1. Take the phone in port P2 off-hook

2. Press # * (three beeps) 0 8 * (three beeps) * (one beep)

3. Hang up the phone

To turn this feature ON:

1. Take the phone in port P2 off-hook

2. Press # * (three beeps) 1 8 * (three beeps) * (one beep)

3. Hang up the phone

Single Tone Detection

This feature allows the LineShare Pro 104 to detect single frequency tones (for the duration of the Single
Tone Detection Timer) from various data devices. It recognizes the following tones:

•

1100Hz Fax CNG tone (if turned ON)

•

1300Hz modem calling tone (if turned ON)

Operation in the Automatic mode and Semi-Automatic mode vary as follows:

Automatic Mode

After the LineShare Pro 104 answers a call, it will monitor the telephone line and transfer calls to the desig-
nated port (set using the Port Tone Assignment parameter) when a single frequency tone is detected. The
Single Tone Detection Timer begins when the LineShare Pro 104 answers the call. After the timer expires, the
LineShare Pro 104 will only transfer calls using the access codes.

Long Range Systems

27

Line Share PRO

«
...
26
27
28
29
30
...
»

Содержание LineShare PRO












































Отзывы:

Нет отзывов