LRS LineShare PRO Скачать руководство пользователя страница 39 | Manualshive

Страница: 39 / 43

LRS LineShare PRO Скачать руководство пользователя страница 39

Port P4 Transfer Code

This feature assigns the access code to transfer a call to port P4.

The Port P4 Transfer Code can be any numeric 1-4 digits not including the # key. See Pound Key Transfer Re-
quired for use with the Port P4 Transfer Code. Do not use a code that is a transfer code for another port on
the LineShare Pro 104.

The factory setting for the Port P4 Transfer Code is 4 4.

To enter a new access code, perform the following steps:

1. Take the phone in port P2 off-hook

2. Press # * (three beeps) 6 4 _ _ _ _ * (three beeps) * (one beep) (blank spaces represent the new

Port P4 Transfer Code)

3. Hang up the phone

A code of 0 0 0 0 disables transfers to this port

Primary Port Selection

This feature designates where the call is routed when tone transfer codes are not detected in the Automatic
mode, or any inbound call when the LineShare Pro 104 is in the Semi-Automatic Mode. Calls can be desig-
nated to any of the 4 ports other than the Secondary Primary Port Selection. Any of the 4 ports can be des-
ignated as the Primary Port. One port cannot be designated to be both the Primary Port and Secondary Port.

The factory setting for Primary Port Selection is port P1 [ # * (three beeps) 7 1 1 * (three beeps) * (one beep) ].

To select transfer to port P2:

1. Take the phone in port P2 off-hook * (three beeps) * (one beep)

2. Press # * (three beeps) 7 2 1 * (three beeps) * (one beep)

3. Hang up the phone

To select transfer to port P3, press # * (three beeps) 7 1 3 * (three beeps) * (one beep)

To select transfer to port P3, press # * (three beeps) 7 1 4 * (three beeps) * (one beep)

Secondary Port Selection

This feature designates where the call is routed when the Automatic No Answer Transfer feature or the Pri-
mary Port Transfer feature is activated.

The factory setting for Secondary Port Selection is port P2 [ # * (three beeps) 7 2 2 * (three beeps) * (one beep) ].

To select transfer to port P1:

1. Take the phone in port P2 off-hook

2. Press # * (three beeps) 7 2 1 * (three beeps) * (one beep)

3. Hang up the phone

To select transfer to port P3, press # * (three beeps) 7 2 3 * (three beeps) * (one beep)

To select transfer to port P3, press # * (three beeps) 7 2 4 * (three beeps) * (one beep)

Long Range Systems

38

Line Share PRO

«
...
37
38
39
40
41
...
»

Содержание LineShare PRO












































Отзывы:

Нет отзывов