LG 42LY770M страница 43 Скачать руководство пользователя

Страница: 43 / 104

206-4271

073 - CH NOT AVBLE (Channel Not Available)

If set to 1 and item 028 CH. OVERIDE is set to 0, a “CHANNEL

NOT AVAILABLE” message is displayed when a user attempts to

direct tune a channel that is not included in the channel lineup.

Note:

This item is not available in the Installer Menu when item

028 CH. OVERIDE is set to 1.

075 - REVERT CH (Revert to Start Channel)

If set to 1 and loss of MPI communication occurs, TV automatically

tunes to the specified Start Channel.

Note:

This item is not available in the Installer Menu when item

004 STRT CHANNEL is set to 255.

077 - QUICK SHUTOFF

Allows end user (patient) to turn OFF TV using mechanical (analog)

Pillow Speaker Channel Up/Down buttons. Patient needs to press

and hold either channel button for time determined by value set.

Set to 0 to disable. Set from 1 to 17 to establish required hold

time of button—from 2 seconds to 10 seconds in half-second

increments.

Note:

This item is not available in the Installer Menu when item

013 SCAN MODE is set to 0.

078 - UPN MSB (UPN Most Significant Byte)

User programmable number, most significant byte readable by

MPI command. Note: Not linked to serial number.

079 - UPN MSB-1 (UPN Most Significant Byte-1)

User programmable number, most significant byte-1 readable by

MPI command. Note: Not linked to serial number.

080 - UPN MSB-2 (UPN Most Significant Byte-2)

User programmable number, most significant byte-2 readable by

MPI command. Note: Not linked to serial number.

081 - UPN LSB (UPN Least Significant Byte)

User programmable number, least significant byte readable by

MPI command. Note: Not linked to serial number.

082 - CHKSM ERROR (Checksum Error)

Enforces rigid MPI checksum validation. Set to 1 for validation.

Set to 0 to disable (does not check checksum on MPI async port).

SPI is always checked.

083 - HANDSHK TIME (Handshake Time)

Adds an additional delay to the handshake time which is 64 msec,

thus relaxing MPI timing requirements to be compatible with PC-

based Windows controlled systems. Range is 0 - 5.

(Timeout = 25.5MS + [25.5 MS* Handshake time].)

084 - PERMANENT BLK (Permanent Block)

Allows Lock (Parental Control) blocking schemes to be permanent

by disabling the blocking hours function. Set to 1 to install Parental

Control restrictions permanently. Set to 0 for user-specified hours

control of blocking schemes.

Note:

This item is not available in the Installer Menu when item

021 V-CHIP is set to 0.

086 - V. MUTE TIME (Video Mute Time)

Use to extend the normal video mute time during channel change.

For example, you may wish to extend the normal video mute time

to prevent the display of encrypted video (i.e., from a Pro:Idiom

encrypted channel) that has not yet been decrypted. When set to

0, the normal video mute time is not extended. Set from 1 to 50 to

increase the normal video mute time in 100 ms step increments up

to a maximum of 5 seconds (e.g., the value of 25 represents 2.5

seconds, or 25 x 100 ms = 2.5 seconds).

088 - EN NOISE MUTE (Enable Noise Mute)

Applicable for analog channels only. If set to 1, audio mutes if no

signal is present.

090 - KEY LOCK

If set to 1, Key Lock is enabled, which means that all display panel

joystick button functions will be locked, i.e., non-functional. Set to

0 to disable Key Lock. Note that all IR features remain functional

regardless of this setting.

091 - HDMI2 ENABLE

Set to 1 to enable HDMI 2 input in DTV Mode. Set to 2 to enable

HDMI 2 input in PC Mode. Set to 0 to disable display panel HDMI

2 input.

094 - SAP MENU EN (2nd Audio Program)

Set to 1 to enable the SAP feature in the Function Menu, when

the Function Menu is available (i.e., TV is not in Pass-through

Mode). Set to 0 to disable the SAP feature in the Function Menu,

when the Function Menu is available.

096 - DEF. ASP. RATIO (Default Aspect Ratio)

Selects default aspect ratio at power up:
0 = Set By Program

1 = 4:3

2 = 16:9 (default)

3 = Just Scan

4 = Zoom

Note:

This item is not available in the Installer Menu unless item

106 ASP RATIO LOCK is set to 0.

097 - AUDIO OUTPUT

Determines availability and signal type/level (fixed speaker,

variable speaker, or fixed line level [amplifier]) of the audio

output to be used by external audio equipment connected to the

SPEAKER OUT / LINE OUT jack on the TV. Set to 0 to disable

audio output. Otherwise, see the table below and set as required

in accordance with audio equipment. See also Reference section,

“External Stereo Speaker Specifications.”

Installer Menu (Cont.)

Содержание 42LY770M









































































































Результаты поиска

Содержание 42LY770M

Отзывы:

Похожие инструкции для 42LY770M

Бренды по названию

Популярные бренды

LG 42LY770M, Руководство по настройке коммерческого режима

Результаты поиска

Содержание 42LY770M

Отзывы:

Похожие инструкции для 42LY770M

Бренды по названию

Популярные бренды