LG 42LY770M страница 80 Скачать руководство пользователя

Страница: 80 / 104

206-4271

Reference: FTG Mode via EBL (Local Configuration)

The following steps outline local FTG configuration of individual TV EBLs using a direct PC-to-TV

(EBL) connection. Refer to the

Free-To-Guest (FTG) Device Configuration Application

User Guide

for further information.

FTG Device Configuration Application software is available online at:

www.lg.com/us/commercial/display-solutions/ftg.

Note:

If the TV CPU is already in FTG Mode, you cannot use this procedure to make changes to the

FTG Channel Map and FTG Installer Menu settings. Refer to FTG Mode information on pages 7 to 9 for

further details.

Note:

If the preceding condition applies, but you wish to switch the TV to FTG Mode via EBL, see

Reference section, “Restoring Factory Defaults on the TV(s),” for further information before proceeding.

Install (if necessary) and launch the FTG Device Configuration Application

(v5.4.8 or higher) on the

PC that will be used to configure the EBL.

Build an FTG Channel Map using the FTG Channel Map Editor in the FTG Channel Map Configuration

Utility (or, if applicable, open an existing FTG Configuration [.rml] file).

Note:

Up to 141 logical channels can be defined in the FTG Channel Map

3. Connect the PC to the TV-LINK CFG jack on the TV’s rear jack panel using a USB-to-TTL serial

cable (TTL-232R-5V-AJ). If necessary, install the device driver on the PC.

4. Turn ON the TV.

Note:

If Installer Menu item 118 POWER SAVINGS is set to 3 (default), the TV must be ON in order

for steps 5 and 6 below to be successful.

5. “Write” the FTG Channel Map to the EBL (switches the EBL from Pass-through Mode to FTG Mode).

Note:

After a “Write” of new data, the TV will briefly display a green text banner that shows the EBL

firmware version and release date.

6. “Read” the current FTG Installer Menu settings from the EBL using the FTG Installer Menu

Configuration Utility. If necessary to make changes to Installer Menu items, “Write” them back to the

EBL in FTG Mode.

7. Save the FTG Channel Map and FTG Installer Menu settings to an FTG Configuration (.rml) file for

future use.

8. Tune the TV to a logical channel in the FTG Channel Map.

Laptop

PILLOW SPEAKER

SPEAKER OUT

LINE OUT

GAME CONTROL

/ MPI

AV IN/AUDIO IN (DVI)

LAN

RESET

RESET UPDATE

PTC SERVICE

(SERVICE ONLY)

OPTICAL

DIGITAL

AUDIO OUT

SERVICE

TV-LINK CFG

VIDEO

L/MONO

-AUDIO-

TV-LINK CFG

Use to connect PC to TV (EBL) for

local FTG Mode via EBL configuration.

USB-to-TTL Serial Cable

Required for local FTG Mode via

EBL configuration.

Содержание 42LY770M









































































































Результаты поиска

Содержание 42LY770M

Отзывы:

Похожие инструкции для 42LY770M

Бренды по названию

Популярные бренды

LG 42LY770M, Руководство по настройке коммерческого режима

Результаты поиска

Содержание 42LY770M

Отзывы:

Похожие инструкции для 42LY770M

Бренды по названию

Популярные бренды