background image

2

206-4271

MODEL and SERIAL NUMBER

The model and serial numbers of this TV are located on the 

back of the cabinet. For future reference, LG suggests that you 

record those numbers here: 

 

Model No._________________ Serial No._______________

WARNING: 

 

TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER (OR BACK). NO USER-

SERVICEABLE PARTS INSIDE. REFER TO QUALIFIED SERVICE PERSONNEL. 

  The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the 

presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude 

to constitute a risk of electric shock to persons.

  The exclamation point within an equilateral triangle is intended to alert the user to the presence of important  

operating and maintenance (servicing) instructions in the literature accompanying the appliance.

WARNING:

TO PREVENT FIRE OR SHOCK HAZARDS, DO NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE.

WARNING:

This product contains chemicals known to the State of California to cause cancer and birth defects or other  

reproductive harm. 

Wash hands after handling

.

POWER CORD POLARIZATION:

This product is equipped with a 3-wire grounding-type alternating current power plug. This plug will fit into the power  

outlet only one way. This is a safety feature. If you are unable to insert the plug fully into the outlet, contact your electrician 

to replace your obsolete outlet. Do not defeat the safety purpose of the 3-wire grounding-type plug.

NOTE TO CABLE/TV INSTALLER: 

This reminder is provided to call the cable TV system installer’s attention to Article 820-40 of the National Electrical Code 

(U.S.A.). The code provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be 

connected to the grounding system of the building, as close to the point of the cable entry as practical.

REGULATORY INFORMATION:

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the 

FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is 

operated in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not 

installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. 

However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause 

harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user 

is encouraged to try to correct the interference by one or more of the following measures:  

• 

Reorient or relocate the receiving antenna.

• 

Increase the separation between the equipment and receiver. 

• 

Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.

• 

Consult the dealer or an experienced radio/TV technician for help.

CAUTION: 

Do not attempt to modify this product in any way without written authorization from LG Electronics U.S.A., Inc. 

Unauthorized modification could void the user’s authority to operate this product.

COMPLIANCE:  

The responsible party for this product’s compliance is: LG Electronics U.S.A., Inc.  

1000 Sylvan Avenue, Englewood Cliffs, NJ 07632, USA • Phone: 1-201-816-2000

WARNING

RISK OF ELECTRIC SHOCK

DO NOT OPEN

© Copyright 2016 LG Electronics U.S.A., Inc.

For Customer Support/Service, please call:    

1-888-865-3026

  

The latest product information and documentation is avail-

able online at: 

www.lg.com/us/commercial

Marketed and Distributed in the United States by LG Electronics U.S.A., Inc.

1000 Sylvan Avenue, Englewood Cliffs, NJ 07632

Содержание 42LY770M









































































































Отзывы: