LG 42LY770M страница 41 Скачать руководство пользователя

Страница: 41 / 104

206-4271

Installer Menu (Cont.)

021 - V-CHIP (Parental Control)

Set to 1 to activate V-Chip (Parental Control) and have it available

to the end user to filter and control or otherwise restrict program

ming content that can appear. Set to 0 to turn the V-Chip feature

Off (not available to user); no programming restrictions can be set.

022 - MAX BLK HRS (Maximum Block Hours)

Sets hours from 0 to 99 for the maximum V-Chip (Parental Control)

block hours. Default setting is for 12 blocking hours.

Note:

This item is not available in the Installer Menu when item

021 V-CHIP is set to 0 or when item 084 PERMANENT BLK is set

to 1.

023 - CAPTION LOCK

If set to 0, captions are OFF when the TV is turned ON. Set to 1

to use the caption setting configured before the TV was turned

OFF when the TV is turned ON.

025 - FUNCTION PRE (Function Preview)

Set to 1 to allow access to the Channel Preview/Banks Setup

Menu via the CH PREVIEW key on Installer Remote. Set to 0 to

disable access to the Channel Preview/Banks Setup Menu.

Note:

This item is only applicable when the TV is in PTC-CTV

Mode.

027 - HOSPITAL MODE

Set according to the speaker selection, the pillow speaker code/

supply voltage and the hospital IR code. If using a Pro:Centric

pillow speaker, select one of the Zenith codes in accordance with

the desired speaker selection. See table below.
When Hospital Mode is enabled and the TV is in Pass-through

Mode, channel banks are also available. Refer to channel banks

information in this document for further details.
Channel banks are not supported if Hospital Mode is set to 0 or on

TVs that are configured for FTG Mode operation.

When Hospital Mode is set to 0 (disabled), both the IR code

that will control the TV and the speaker selection depend on the

Installer Menu item 020 FEATURE LEVEL setting.

Note:

The default setting (254) is not selectable in the Installer

Menu. If you ever need to restore the default setting, you must

reload the factory default settings. See item 117 description and/or

Reference section, “Restoring Factory Defaults on the TV(s),” for

further information.

Note:

In the Installer Menu, an informational code is displayed

at the right of each Hospital Mode value. Each code consists of

three characters. The first character—T, P, or B—identifies the

speaker: TV, Pillow, or Both. The second character—Z, P, R,

or D—identifies the pillow speaker code: Zenith, Philips, RCA, or

Disabled. The third character—1 or 2—identifies the bed number.

In the table above, each bolded character represents an element of

the Hospital Mode code.

Value

Speaker

Pillow Speaker

Code/Voltage

Hospital IR Code

000

Determined by

item 020 setting

enith (+12v)

Determined by item

020 setting

001

illow Only

enith (+12v)

Zenith Bed #

002

illow Only

enith (+12v)

Zenith Bed #

017

illow Only

hilips (+5v)

Zenith Bed #

018

illow Only

hilips (+5v)

Zenith Bed #

033

illow Only

CA (-5v)

Zenith Bed #

034

illow Only

CA (-5v)

Zenith Bed #

065

V Only

enith (+12v)

Zenith Bed #

066

V Only

enith (+12v)

Zenith Bed #

081

V Only

hilips (+5v)

Zenith Bed #

082

V Only

hilips (+5v)

Zenith Bed #

097

V Only

CA (-5v)

Zenith Bed #

098

V Only

CA (-5v)

Zenith Bed #

129

oth Pillow & TV

enith (+12v)

Zenith Bed #

130

oth Pillow & TV

enith (+12v)

Zenith Bed #

145

oth Pillow & TV

hilips (+5v)

Zenith Bed #

146

oth Pillow & TV

hilips (+5v)

Zenith Bed #

161

oth Pillow & TV

CA (-5v)

Zenith Bed #

162

oth Pillow & TV

CA (-5v)

Zenith Bed #

254

V Only

isabled (0v)

Zenith Bed #

028 - CH. OVERIDE (Channel Override)

This item either allows or restricts tuning of channels that are NOT

in the PTC Channel Map.

If set to 1, end users can tune channels

that are not in the PTC Channel Map by direct keypad entry. If

set to 0, users are restricted to only the channels that are in the

PTC Channel Map. In the case of CPU-CTV Mode, there are no

channels in the PTC Channel Map; therefore, direct keypad entry

is not available. Also, when this item is set to 0, the PTC Channel

Map (PTC-CTV Mode)/CPU channel lineup (CPU-CTV Mode)

is locked, and user access to channel settings in the TV setup

menus is restricted.

Note:

This item is not applicable when the TV is in FTG Mode.

029 - OLD OCV (On Command Video™)

Set to 1 to remap the PTC’s direct tune channels for Aux inputs

from 13x to 9x. This allows 2-digit only tuning systems (i.e., legacy

OCV) to direct tune Aux inputs. See also Reference section, “TV

Aux Input Configuration.”

030 - ACK MASK

MPI Communication Parameter. When set to 1, enables ACK

feature of MPI.

031 - POLL RATE

MPI Communication Parameter. Selects poll rate for MPI. Step

size of 16 ms. Changing from default may affect communication

via MPI.

Содержание 42LY770M









































































































Результаты поиска

Содержание 42LY770M

Отзывы:

Похожие инструкции для 42LY770M

Бренды по названию

Популярные бренды

LG 42LY770M, Руководство по настройке коммерческого режима

Результаты поиска

Содержание 42LY770M

Отзывы:

Похожие инструкции для 42LY770M

Бренды по названию

Популярные бренды