Leuze BCL 40 Скачать руководство пользователя страница 79

Страница: 79 / 91

Leuze

electronic

Communicating with the Device

Leuze electronic

BCL 40

TNT

35/7-2

Detect code

9.3.2

"Online" Commands for System Control

Activate sensor input 1

Deactivate sensor input 1

Command

’CC’

Description

Reads the code type and contents of an unknown label without storing it
in Setup.

Parameter

Acknowledge-
ment

xxyyzzzzzz
The acknowledgement is the same as that of the "autoConfig" function.

Command

’+’

Description

Activates decoding (sensor input 1). A signal can be simulated on sensor
input 1 with this command.

Parameter

Acknowledge-
ment

Command

’-’

Description

Deactivates decoding (sensor input 1). A signal can be simulated on sen-
sor input 1 with this command.

Parameter

Acknowledge-
ment

Buy: www.ValinOnline.com | Phone 844-385-3099 | Email: [email protected]

Содержание BCL 40




























































































Результаты поиска

Содержание BCL 40

Отзывы:

Бренды по названию

Популярные бренды

Leuze BCL 40, Техническое описание

Результаты поиска

Содержание BCL 40

Отзывы:

Бренды по названию

Популярные бренды