manualshive.com logo in svg

Leuze BCL 40, Техническое описание

Поделиться
Скачать
Leuze BCL 40 Скачать руководство пользователя страница 59

     Leuze

electronic

Commissioning

Leuze electronic

BCL 40

57

TNT

 35/7-2

4

V

Wiring description

The 9 pin Sub D RS 232 Terminal connector (male) has the following pin assignments:

Using a PC and a terminal program, the set-up program of the BCL 40 can be called, online
commands sent and data received via this interface terminal.

Notice!

In setting 2 ("operation") of the operating mode switch, the terminal connector can be used
as a data monitor. In this case, data sent from the BCL 40 (jumper in figure 7.1 in lower po-
sition) or data received from host (jumper in figure 7.1 in upper position) can be logged. The
data protocol is set by the host interface in the latter case.

Configuration software

Leuze offers a convenient program "BCL Configuration Tool" for setting the required device
parameters (see chapter 5 "Accessories / Order Designation").

7.3.3

Setting Parameters "Offline" 

Setting parameters

The parameters are programmed on a PC without direct connection to the BCL 40 ("Offline"
programming) and saved in a file (parameter file).

Downloading parameters

After successful programming, the parameters are loaded into the BCL 40 (parameter
"Download"). This causes the required parameters to be transferred from the host computer,
or a computer connected to the interface terminal of the MA 10, to the BCL 40 or MA 10,
respectively. 

Pin 1

NC

not used

Pin 2

RXD

receive signal of the RS 232 service interface

Pin 3

TXD

transmit signal of the RS 232 service interface

Pin 4

NC

not used

Pin 5

GND

signal reference potential 0VDC

Pin 6

RXD_Host

receive signal of the host interface

Pin 7

NC

not used

Pin 8

NC

not used

Pin 9

reserved

for service purposes only

Buy: www.ValinOnline.com | Phone 844-385-3099 | Email: [email protected]

Содержание BCL 40




























































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды