manualshive.com logo in svg

Leuze BCL 40, Техническое описание

Поделиться
Скачать
Leuze BCL 40 Скачать руководство пользователя страница 57

     Leuze

electronic

Commissioning

Leuze electronic

BCL 40

55

TNT

 35/7-2

4

V

Current parameter set

In this parameter set, the current settings for all device parameters are stored. If the BCL 40
is in "stand alone" operation, the parameter set is stored in the EEPROM of the BCL 40. If
an MA 10 is also used, the parameter set is stored in EEPROM of the MA 10 and a copy
thereof in the EEPROM of the BCL 40. The current parameter set can be stored in three
ways:

• by changing and storing the current parameter set using the integrated SETUP pro-

gram of the BCL 40

• by copying (parameter "Download") a valid parameter set from the host computer 

(e.g. a PC or PLC).

• by means of an off-line setup with the program "BCL Configuration Tool" 

The current parameter set is loaded into the memory of the BCL 40:

• each time the supply voltage is connected
• after a "warm start" reset, as well as a software reset

Figure 7.2:

Block diagram storage concept for parameter sets

Notice!

By storing all current and customer-specific values in the connector unit MA 10, a connected
BCL 40 can be exchanged without difficulty since all parameters are maintained.

ROM

Default PS (2)

EEPROM

Current PS (0)

RAM

Working copy of current PS

ROM

Default PS (2)

EEPROM

Current PS (0)

RAM

Working copy of current PS

ROM

Customer-

specific 

Parameter set (1)

EEPROM

Current 

parameter set (0)

MA 10

BCL 40

BCL 40

Terminal 
program on 
PC

Parameter 
"Down-
load" from 
HOST

Parameter 
"Download" 
from HOST

Terminal 
program on 
PC

BCL 40

with MA 10

BCL 40 "Stand alone"

"2" = parameter set with factory default settings
"1" = customer-specific parameter set
"0" = current parameter set

Buy: www.ValinOnline.com | Phone 844-385-3099 | Email: [email protected]

Содержание BCL 40




























































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды