Leuze BCL 40 Скачать руководство пользователя страница 35

Страница: 35 / 91

Leuze

electronic

Installation

Leuze electronic

BCL 40

TNT

35/7-2

Independent mounting BCL 40 / MA 10

Independent mounting of the BCL 40 and MA 10 is necessary when

• the available mounting depth is not sufficient for both devices, e.g. is less than

85 mm,

• or access to the mounting location of the scanner is difficult, but easy installation,

commissioning and service are required, or

• the operating status LEDs on the back side of the MA 10 must be easily seen.

Figure 6.4:

Mounting examples for the BCL 40 and MA 10 mounted independently

You can mount the individual devices in the following way as already described above:

• using the dovetail groove of the BCL 40 or the MA 10 and the corresponding mount-

ing accessories

• using the fastening threads on the back- or underside of the devices
• the connector unit can additionally be mounted using two M5 screws into the

threaded holes that are otherwise used for fastening the BCL 40. The threaded holes
have M5 threads.

Buy: www.ValinOnline.com | Phone 844-385-3099 | Email: [email protected]

Содержание BCL 40




























































































Результаты поиска

Содержание BCL 40

Отзывы:

Бренды по названию

Популярные бренды

Leuze BCL 40, Техническое описание

Результаты поиска

Содержание BCL 40

Отзывы:

Бренды по названию

Популярные бренды