manualshive.com logo in svg

Leuze BCL 40, Техническое описание

Поделиться
Скачать
Leuze BCL 40 Скачать руководство пользователя страница 17

     Leuze

electronic

Description

Leuze electronic

BCL 40

15

TNT

 35/7-2

4

V

3.3.2

Device construction MA 10

Figure 3.4:

Connector unit MA 10

Device variations MA 10

The MA 10 is available in four models:

•  MA 10 100 with host interface module RS 485
•  MA 10 110 with host interface module RS 232
•  MA 10 120 with host interface module TTY
•  MA 10 130 with host interface module RS 422

All modules are galvanically isolated, i.e. they are EMC interference protected and immune
to differences in voltage potentials across long cable lengths.

Notice!

Only the type MA 10 100 can be used as a multiNet slave unit.

Cable screw glands PG11
for the power supply

Cable screw glands PG11
for the power supply

4 fastening threads M4 on the 
base of the device

4 Status-LEDs 
on the rear

Mounting holes for the 
BCL 40 with M4 
screws

15 pin Sub-D 
connector 

Dovetail fastening 
grooves

Buy: www.ValinOnline.com | Phone 844-385-3099 | Email: [email protected]

Содержание BCL 40




























































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды