manualshive.com logo in svg

Leuze BCL 40, Техническое описание

Поделиться
Скачать
Leuze BCL 40 Скачать руководство пользователя страница 12

Description

Leuze

electronic

10

BCL 40

Leuze electronic

3

Description

3.1

The Bar Code Readers BCL 40

The bar code reader BCL 40 is a high-speed scanner with integrated decoder for all bar
codes currently in use, e.g. 2/5 Interleaved, EAN, etc. 

The many possible configurations of the device allow its adaptation to a multitude of reading
tasks. Due to its compact size and short minimum reading distance, the BCL 40 can also be
used in very compact spaces.

Together with the connector unit MA 10, it can easily be adapted for use with various inter-
faces, thus allowing additional processing by other systems. The MA 10 connector unit can
also be used to network together several BCL 40 devices and to simplify electrical installa-
tion.

On demand, the BCL 40 can be equipped with an integrated heater. This variant is used
primarily in low-temperature and outdoor applications. The optional heater is constructed
such that no heat transfer occurs between the separately mounted technical unit and the
scanner housing. In addition, the front cover of the device is heated, preventing the forma-
tion of condensation which would affect the reading function. The reading curves differ with
respect to the standard type in the construction of the front cover, which is modified by
heating filaments.

3.2

Features of the BCL 40

3.2.1

Performance features

• Compact device dimensions (W x H x D) 90 x 120 x 43mm
• Reading height of 70 mm at a distance of 10mm
• Maximum reading distance up to 700mm (depending on type of optics)
• Raster or line scanner (R1 = raster, S = single line) max. 1200scans/s
• A switched input for triggering a read process using sensors
• Automatic monitoring of the read quality with the "autoControl" function
• Automatic recognition of the bar code type using "autoConfig"
• All device parameters can be set by software
• Heavy-duty housing of protection class IP 65 with corresponding cable
• RS 232 or RS 485 interface to host
• Extensive formatting possibilities for data output
• Reference code (comparison code)

Buy: www.ValinOnline.com | Phone 844-385-3099 | Email: [email protected]

Содержание BCL 40




























































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды