manualshive.com logo in svg

Leuze BCL 40, Техническое описание

Поделиться
Скачать
Leuze BCL 40 Скачать руководство пользователя страница 70

Communicating with the Device

Leuze

electronic

68

BCL 40

Leuze electronic

9.2.4

Communication

Figure 9.7:

"Communication" menu, standard setting

Select the desired baud rate, the stop bits, the data bits and the parity here. In addition,
several different handshake modes and protocols can be set here.

The RK512/3964 protocol can also be selected here. The individual parameters for this
protocol can be found in the tree-structure configuration and Communication -> Customer
Interface -> 3964 / RK 512 Protocol.

Attention! 

If the BCL 40 is operated in a network ("Leuze multiNet"), no changes may be made here.
The scanner automatically sets itself to the multiNet protocol!

After equal scans 
reach

If this item is activated, the read result is output immediately after the 
bar code is decoded. If the item is deactivated, the read result is sent 
only after the trigger signal is returned (= end of reading gate).

Time

For test purposes.
If the scanner is activated, the reading gate is automatically closed 
by the scanner after this preset time has elapsed. 

Scans without info

Following a successful read, the scanner waits for this number of 
scans (sequential scans with no read result) before it automatically 
deactivates itself.

Option

Explanation

Buy: www.ValinOnline.com | Phone 844-385-3099 | Email: [email protected]

Содержание BCL 40




























































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды