manualshive.com logo in svg

Leuze BCL 40, Техническое описание

Поделиться
Скачать
Leuze BCL 40 Скачать руководство пользователя страница 18

Specifications

Leuze

electronic

16

BCL 40

Leuze electronic

4

Specifications

4.1

Technical Data BCL 40 Standard Version

Optical Data
Light source

Laser diode 650nm

Scanning rate

BCL with N, M, F optics: 1200scans/s
BCL with L optics: 900scans/s

Resolution

0.1mm … 1.2mm 
module width

Beam deflection

by means of rotating polygon mirror wheel

Reading distance

0 … 700mm (depending on type of optics: N, M, F, L), see 
chapter 4.5.4 "Reading curves BCL 40 standard version"

Reading field opening

70mm at a distance of approx. 10mm (see chapter 4.5.4 
"Reading curves BCL 40 standard version")

Grid (R1)

8 lines

Grid field

specified is the area from the first to the last laser beam as 
a function of distance to the scanner
22mm at 100mm scanner distance 
33mm at 200mm scanner distance
45mm at 300mm scanner distance
65mm at 500mm scanner distance
95mm at 800mm scanner distance

Single line (S)

1 line

Optical window

glass with scratch-resistant Indium coating

Laser safety class

2

Code types

2/5 Interleaved; Code 39; Code 128; EAN 8; 13; EAN 128; 
UPC; Codabar; Add-On for EAN / UPC

Software features

selectable output format, autoConfig, autoControl, refer-
ence code comparison, multiple read, real time decoding, 
adjustment mode, diagnosis, reading gate control, control 
of switching inputs and switching outputs, etc.

Electrical data
Interface type

can be switched between RS 232 and RS 485, additional 
service interface (RS 232)
TTY / RS 422 optional with MA 10

Baud rate

110 … 57600Bd (host interface only)

Data formats

data bits: 7, 8, 9
parity: None, Even, Odd
Stop bit: 1, 2

Protocols

with/without frame protocol
ACK/NAK, 3964 (R) RK 512, RTS/CTS
X ON / X OFF, multiNet plus

Ports 

1 switching input

LED green

device ready (Power On)

Buy: www.ValinOnline.com | Phone 844-385-3099 | Email: [email protected]

Содержание BCL 40




























































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды