manualshive.com logo in svg

Leuze BCL 40, Техническое описание

Поделиться
Скачать
Leuze BCL 40 Скачать руководство пользователя страница 77

     Leuze

electronic

Communicating with the Device

Leuze electronic

BCL 40

75

TNT

 35/7-2

4

V

Call the setup program

Notice!

Read/write operations cannot be carried out in the service mode. The set-up program must
always be ended in order to return to normal operation.

"autoConfig"

Command

’E’

Description

Calls the set-up program. The main menu of the set-up program is dis-
played.

Parameter

no

Acknowledge-
ment

Acknowledgement, ’Load Parameter Set’
’ ’
’ Setup’
’-------------------------------------------------’
’ 1: Language’
’ 2: Decode Setup’
’ ’
’Enter:’

Command

’CA’

Description

Activates or deactivates the "autoConfig" function. Certain label reading 
parameters are programmed automatically in the setup by the labels 
which are read while the "autoConfig" function is active.

Parameter

’+’

activates "autoConfig"

’/’

rejects the last code read

’-’

deactivates "autoConfig" and stores the decoded data in the current 
parameter set

Acknowledge-
ment

’xx yy zzzzzz’ (only with ’CA+’)
xx:

Code type of the read code
’01’ 2/5 Interleaved
’02’ Code 39
’06’ UPC (A, E)
’07’ EAN
’08’ Code 128, EAN 128
’10’ Add-on for EAN/UPC
’11’ Codabar

yy

No. of digits of the read code

zzzzzz 

Contents of the decoded label. The 

’,

 appears if the label was not 

correctly read.

Buy: www.ValinOnline.com | Phone 844-385-3099 | Email: [email protected]

Содержание BCL 40




























































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды