manualshive.com logo in svg

Leuze BCL 40, Техническое описание

Поделиться
Скачать
Leuze BCL 40 Скачать руководство пользователя страница 13

     Leuze

electronic

Description

Leuze electronic

BCL 40

11

TNT

 35/7-2

4

V

3.2.2

Added features with MA 10

• Device status display with 4 LEDs
• RS 485 interface with electrical isolation for networking several devices
• Alternative interface RS 232, RS 422 or TTY using a selectable interface module with 

electrical isolation for directly connecting to the host

• Two hardware switched outputs for status signals
• Additional switched input for the definition of reference code 1
• Simple electrical connection via double terminal clamps, i.e. both the power supply 

and the interface circuits can easily be connected in series.

• Heavy-duty housing of protection class IP 65
• 2 parameter sets can be stored locally in the MA 10

(current parameter set, customer-specific parameter set)

• Built-in RS 232 service interface for fast commissioning or troubleshooting on site 

using a PC or programming device

• Switch for the "autoConfig" function

3.2.3

Modular Concept

BCL 40 "Stand alone"

The bar code reader BCL 40 can be operated as an individual "stand alone" (

€

) device.

Electrical connection of the power supply, interface and switched input are centrally made
via a 15 pin SubD socket. 

For connection, it is best to use the 15 conductor connection cable from Leuze. The require-
ments for protection class IP 65 are fulfilled when using this cable only (see chapter 5
"Accessories / Order Designation"). 

BCL 40 with MA 10 

When using several BCL 40 units or under rough environment conditions, the installation of
one connector unit MA 10 for each BCL 40 unit is recommended. 

Electrical connection, commissioning, and service can be comfortably carried out in a short
period of time. 

The BCL 40 and MA 10 can be mounted directly together (

ó

) or arranged separately next

to each other. When mounted separately (

ì

), the two units are connected by a cable.

Protection class IP 65 is maintained when the sealed accessory cable is used (see chapter
5 "Accessories / Order Designation").

Buy: www.ValinOnline.com | Phone 844-385-3099 | Email: [email protected]

Содержание BCL 40




























































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды