Lamtec ETAMATIC Скачать руководство пользователя

Страница: 86 / 136

Appendix



Fault 600

The control unit has locked up



Call-up running text and follow it’s instructions
Check wiring and extend signal transmitters e.g.
–

safety interlock chain boiler

–

safety interlock chain gas

–

air pressure monitor

–

safety interlock chain oil (special function)

–

fuel selection (special function)

–

external high firing-rate acknowledgement

–

external ignition position acknowledgement

Check motor limit stops
otherwise
Extend program monitoring time



see P 777 (only with level 1 access), see also E14



Fault 607

The ignition position acknowledgement signal drops during the ignition sequence



(terminal 74)

NOTICE!
The ignition position acknowledgement signal must be present up to the end of the ignition
sequence (to the end of the 2

safety period).

If fault appears directly before ignition:

Maybe the oil pump has not enough time to build up pressure



Parameter 782



Fault 734

For one of the processors the pre-ventilation is still running while the other one already termi-
nated the pre-ventilation.

Check high load indication



Re-enter range limits

Содержание ETAMATIC









































































































































Результаты поиска

Содержание ETAMATIC

Отзывы:

Похожие инструкции для ETAMATIC

Бренды по названию

Популярные бренды

Lamtec ETAMATIC, Руководство пользователя

Результаты поиска

Содержание ETAMATIC

Отзывы:

Похожие инструкции для ETAMATIC

Бренды по названию

Популярные бренды