manualshive.com logo in svg

Lamtec ETAMATIC, Руководство пользователя

Поделиться
Скачать
Lamtec ETAMATIC Скачать руководство пользователя страница 112

111

9  

Appendix

Technical data of the Namur input: U

O

 = 8,2V; Ik = 8,2mA, +/- 5%

–

make threshold: max 2.1 mA (typical 1.8 mA)

–

break threshold: max. 1.2 mA (type 1.4 mA)

–

linearity error: < 0,1% v. E.

–

temperature drift: < 75 ppm/K (type. 60ppm/K)

Direct connection of Speed sensor (actual version)

This option allows you to connect a inductive sensor for revolution pickup directly. It could be 
a NAMUR type or a three wired type. The selection of the type and the range is only factory 
setting. Sensor NAMUR type is connected to terminal 42 and 43, three wired type to terminal 
42,43 and 44 or 22.
Speed nominal range (164...819 digit):
•

I        30 ...   300 pulses / min.  

•

II     600 ... 7200 pulses / min.

•

III    300 ... 3600 pulses / min. (standard)

•

IV     60...    600 pulses / min

lower limit (152 digit) / upper limit (991 digit)
•

I        20 ...   350 pulses / min.  

•

II     355 ... 8430 pulses / min.

•

III    175 ... 4220 pulses / min. (standard)

•

IV     40...    700 pulses / min

If the set pulse range is exceeded the value remains at the upper end of the range (higher 
pulse numbers are ignored). Below the measuring range the signal goes to approx. 0 - 7 digit. 
The standard setting is range III (i.e. on motors with 3000 rpm at 50 Hz, 1 pulse per revolution)

WARNING!
Make sure that the selected measuring range is not exceeded, otherwise speed changes in 
excess of this will no longer be detected.

Owing to the large number of usable transducers LAMTEC has only one two wire element and 
one three wire element in it’s product range. It is selected in that way, that it covers a number 
of measuring tasks. Other transducers only on enquiry or direct from the company Turck.

Technical Data

     linearity error

< 0,1% v. E.

     temperature drift

< 75 ppm/K (typical 60 ppm/K)

Namur input

U

O

 = 8,2 V; Ik = 8,2 mA, +/- 5%

     make threshold:

max. 1,98 mA (typical 1,8 mA), +/- 5%

     break threshold:

max. 1,62 mA (typical 1,4 mA), +/- 5%

Switch input
     make threshold:

6,2V

     break threshold:

4,5V

Measuring method

period duration measurement over 5 periods

Input pulse width:

>200 µs

Temperature range:

0…60 °C / 32°F...140°F

Usable Namur trans-
mitters

all Turck sensors, which contain Y0 or Y1 in their type designa-
tion.

Содержание ETAMATIC









































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды