Lamtec ETAMATIC Скачать руководство пользователя

Страница: 36 / 136

Commissioning

5.3

Fault

5.3.1

Reading Faults

NOTICE!
If you want to read the other display values up to the time of the fault press key 16. All display
values are frozen.

5.3.2

Resetting Faults

5.3.3

Recall Fault History

The ETAMATIC stores the last 10 faults with the associated data of the running time counter.
Requirement: ETAMATIC must not be in fault condition.

CAUTION!
If it is certain that the ETAMATIC has carried a voltage at all times since the last fault, it is pos-
sible, that from the present output of the running time counter and the current time, to deter-
mine at which time the fault occurred.

Red fault LED is on



Press key 17 until "Status" appears.



The display shows a plain text

message (incl. running time counter)
Press key „ENTER“ drücken



Plain text message appears on the

display (incl. output of the running time counter)

Press key RESET



Alternatively:



Use an external switch to send a short signal (min. 2 sec.) to terminal 5.



the error is cleared!

Press key 17 until the display shows "Status".

Press key 3



the display shows the last fault code

Press key 11 (Enter)



the display shows the associated plain text and the run-

ning time hours.

Press key 3 again



The display shows the last but one fault code.

Press keys 3 and 2 to browse through the fault history.

Содержание ETAMATIC









































































































































Результаты поиска

Содержание ETAMATIC

Отзывы:

Похожие инструкции для ETAMATIC

Бренды по названию

Популярные бренды

Lamtec ETAMATIC, Руководство пользователя

Результаты поиска

Содержание ETAMATIC

Отзывы:

Похожие инструкции для ETAMATIC

Бренды по названию

Популярные бренды