manualshive.com logo in svg

Lamtec ETAMATIC, Руководство пользователя

Поделиться
Скачать
Lamtec ETAMATIC Скачать руководство пользователя страница 121

120

9  

Appendix

9.23

Run to Shut-off Limits

Like every control system, the ETAMATIC has tolerances, which affect the accuracy of the set-
tings. You have influence of these tolerances of the ETAMATIC with the parameter settings.
When you adjust the combustion system, ensured that there is a safe and stable flame. To 
verify this, it is necessary that you test the combination of settings not only by regarding the 
required values that you have set, but also the so-called shut-down limits. This are actuator 
settings which the ETAMATIC just takes without switching off.
Perform this test for the whole load range and for all operating modes.
This test may only be dispensed with if:
–

the installation is fitted with fail-safe O

2

 or CO monitoring which can trigger a burner shut-

down if there is incomplete combustion

or
–

the installation is fitted with fail-safe O

2

 trim/ CO control, which compensates the combus-

tion tolerances

or 
–

You ensure that the requested mode, has as much excess air over the whole range, that 
the tolerances of the ETAMATIC are of no consequence

or
–

the parameters in the ETAMATIC are set in that way, that the air defficiency tolerances 
have 0 digit, i.e. there is only tolerance on the excess air side.

WARNING!
If you waive to check the shut-down limits because of one of these measures, you should 
check the effectiveness of that measure instead, e.g., if there is O

2

 / CO monitoring or control, 

the stability of ignition should be tested at the shut-down value set

WARNING!
Due to verification in respect of authorities, test houses, quality management systems, liability 
issues, etc., we strongly recommend that you document any running to shut-down limits

Adjust setpoint value of the continuous channel in the air deficiency direction until the actual 
value feedback has changed by the set number of points (monitoring band)
Check combustion

Reset setpoint value to the next continuous channel in air deficiency direction.

Check combustion

Repeat, until all continuous channels are checked at their limits.

press key 12

press keys 2 and 3 to run to the load point for checking it
wait until the system has run to that point
enter password

press key 14 one time (setting)

Содержание ETAMATIC









































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды