Lamtec ETAMATIC страница 85 Скачать руководство пользователя

Страница: 85 / 136

Appendix

E13



Fault 141...145

Only with three-point step control output.
The feedback values vary more rapidly than the maximum specified in the parameter section

Check potentiometers for short-circuits
otherwise
Change potentiometers

E14

Text message Channel X does not reach aeration position in time and/or fault 600.

The range monitoring during pre-ventilation results in a too low limit stop value of the feedback
potentiometer. The upper and lower limit value are not reached during pre-ventilation.
Check potentiometer



Check continuous feedback value
Compare range limits with feedback’s stop values
If necessary, re-enter range limits

NOTICE!
If limit switches are adjusted after a curve has been programmed, the range limits must be re-
entered.

Maybe the control of the motor is defective
check relay module
check wiring

E18



Fault 451...456

A control element has left the ignition range after the ETAMATIC had detected the ignition po-
sition.

Possible causes:
–

control element oscillating

–

wiring fault

–

holding torque of motor too low

Содержание ETAMATIC









































































































































Результаты поиска

Содержание ETAMATIC

Отзывы:

Похожие инструкции для ETAMATIC

Бренды по названию

Популярные бренды

Lamtec ETAMATIC, Руководство пользователя

Результаты поиска

Содержание ETAMATIC

Отзывы:

Похожие инструкции для ETAMATIC

Бренды по названию

Популярные бренды